Lenovo S50-30 Lenovo S50-30 All-In-One PC Hardware Maintenance Manual - Page 41

Replacing the converter board, Remove the computer stand. Refer to Removing the frame stand

Get Lenovo S50-30 PDF manuals and user guides View all Lenovo S50-30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Step 6. Remove the screw that secures the camera to the front bezel. 1 Step 7. Slide the camera out 2 and disconnect the data cable from the camera. 3 Step 8. To install the new camera: a. Connect the data cable to the new camera. b. Line up the holes in the new camera with the mounting holes on the front bezel and secure the new camera with the screw. Step 9. Reattach the rear cover and secure it with the screws. Step 10. Reattach the computer stand. Replacing the converter board Note: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover. To replace the converter board: Step 1. Step 2. Step 3. Step 4. Step 5. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Unplug all power cords from electrical outlets. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to "Left and right view" and "Rear view" for help with locating the various connectors. Remove the computer stand. Refer to "Removing the frame stand", "Removing the monitor stand", or "Removing the transformer stand". Remove the rear cover. Refer to "Removing the rear cover". Chapter 8. Replacing hardware 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
Step 6.
Remove the screw that secures the camera to the front bezel.
1
Step 7.
Slide the camera out
2
and disconnect the data cable from the camera.
3
Step 8.
To install the new camera:
a.
Connect the data cable to the new camera.
b.
Line up the holes in the new camera with the mounting holes on the front bezel and secure the
new camera with the screw.
Step 9.
Reattach the rear cover and secure it with the screws.
Step 10. Reattach the computer stand.
Replacing the converter board
Note:
Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover.
To replace the converter board:
Step 1.
Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating
system, and turn off the computer and all attached devices.
Step 2.
Unplug all power cords from electrical outlets.
Step 3.
Disconnect all cables attached to the computer. This includes power cords, input/output (I/O)
cables, and any other cables that are connected to the computer. Refer to “Left and right view”
and “Rear view” for help with locating the various connectors.
Step 4.
Remove the computer stand. Refer to “Removing the frame stand”, “Removing the monitor stand”,
or “Removing the transformer stand”.
Step 5.
Remove the rear cover. Refer to “Removing the rear cover”.
Chapter 8
.
Replacing hardware
35