Lenovo ThinkPad X22 English - ThinkPad X22 Service and Troubleshooting guide - Page 34

Problem, Solution, Config, Disable, Press F1 for IBM BIOS Setup Utility

Get Lenovo ThinkPad X22 PDF manuals and user guides View all Lenovo ThinkPad X22 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Solving computer problems Also make sure that the device from which the computer starts is enabled by checking that there is no ! mark preceding the device name. Problem: The computer does not respond. Solution: IRQs for the PCI are all set as 11. The computer does not respond because it cannot share the IRQ with other devices. Refer to the ThinkPad Configuration Program. Problem: Windows NT does not start; however, the message saying that Windows NT is loading remains on the screen. Solution: The USB setting might have been changed to Enabled. If so, it might cause a conflict in allocating memory resources during startup. Disable the setting, using the BIOS Setup Utility as follows: 1. Turn your computer off and then on again; then, while the message, "Press F1 for IBM BIOS Setup Utility," is displayed at the lower left of the screen, press the F1 key to start the BIOS Setup Utility. The BIOS Setup Utility menu appears. 2. With the cursor key, select Config; then press Enter. 3. Select USB by pressing Enter. 4. With the cursor key, select Disable; then press Enter. 5. Press F10 and Enter to save this setting and exit this utility. 26 ThinkPad® X22 Service and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Also make sure that the device from which the computer starts is enabled by
checking that there is no ! mark preceding the device name.
Problem:
The computer does not respond.
Solution:
IRQs for the PCI are all set as 11. The computer does not respond
because it cannot share the IRQ with other devices. Refer to the ThinkPad
Configuration Program.
Problem:
Windows NT does not start; however, the message saying that
Windows NT is loading remains on the screen.
Solution:
The USB setting might have been changed to Enabled. If so, it might
cause a conflict in allocating memory resources during startup. Disable the
setting, using the BIOS Setup Utility as follows:
1.
Turn your computer off and then on again; then, while the message,
“
Press F1 for IBM BIOS Setup Utility,
”
is displayed at the lower left of the
screen, press the F1 key to start the BIOS Setup Utility. The BIOS Setup
Utility menu appears.
2.
With the cursor key, select
Config
; then press Enter.
3.
Select
USB
by pressing Enter.
4.
With the cursor key, select
Disable
; then press Enter.
5.
Press F10 and Enter to save this setting and exit this utility.
Solving computer problems
26
ThinkPad
®
X22 Service and Troubleshooting Guide