LevelOne FCS-0020 User Manual - Page 13

Installation - FCS-0020/WCS-0020

Get LevelOne FCS-0020 PDF manuals and user guides View all LevelOne FCS-0020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Installation - FCS-0020/WCS-0020 1. Assemble the Camera Screw the supplied antenna to the mounting point on the rear. Attach the Camera Mount to the camera. 2. Connect the LAN Cable Connect the FCS-0020/WCS-0020 to a 10/100BaseT hub or switch, using a standard LAN cable. For the WCS-0020, plugging in the LAN cable will disable the Wireless interface. Only 1 interface can be active at any time. The LAN cable should only be connected or disconnected when the camera is powered OFF. Attaching or detaching the LAN cable while the camera is powered on does NOT switch the interface between wired and wireless. The first time you connect to the camera, you should connect the LAN cable and configure the WCS-0020 with appropriate settings. Then you can unplug the LAN cable and power off the camera. The WCS-0020 will be in wireless interface when you power on the camera again. 3. Power Up Connect the supplied 5Vpower adapter to the FCS-0020/WCS-0020 and power up. Use only the power adapter provided. Using a different one may cause hardware damage. 4. Check the LEDs • The Power LED will turn on briefly, then start blinking. It will blink during startup, which takes 15 to 20 seconds. After startup is completed, the Power LED should remain ON. • The Network LED should be ON. For more information, refer to Physical Details - FCS-0020/WCS-0020 in Chapter 1. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
7
Installation - FCS-0020/WCS-0020
1. Assemble the Camera
Screw the supplied antenna to the mounting point on the rear.
Attach the Camera Mount to the camera.
2. Connect the LAN Cable
Connect the FCS-0020/WCS-0020 to a 10/100BaseT hub or switch, using a
standard LAN cable.
For the WCS-0020, plugging in the LAN cable will disable the
Wireless interface. Only 1 interface can be active at any time.
The LAN cable should only be connected or disconnected
when the camera is powered OFF. Attaching or detaching the
LAN cable while the camera is powered on does NOT switch
the interface between wired and wireless.
The first time you connect to the camera, you should connect
the LAN cable and configure the WCS-0020 with appropriate
settings. Then you can unplug the LAN cable and power off
the camera. The WCS-0020 will be in wireless interface when
you power on the camera again.
3. Power Up
Connect the supplied 5Vpower adapter to the FCS-0020/WCS-0020 and power up.
Use only the power adapter provided. Using a different one may cause hardware
damage.
4. Check the LEDs
•
The
Power
LED will turn on briefly, then start blinking. It will blink during startup,
which takes 15 to 20 seconds.
After startup is completed, the
Power
LED should
remain ON.
•
The
Network
LED should be ON.
For more information, refer to
Physical Details - FCS-0020/WCS-0020
in Chapter 1.