Lexmark Optra C710 User's Guide - Page 168

154

Chapter 8: Understanding printer messages

52 Flash Full

There is not enough space available to hold the resources you want to store in

flash memory.

•

Press

Go

to clear the message and continue processing. Downloaded fonts

and macros not previously stored in flash memory or disk are deleted.

•

Reset the printer. Press

Menu>

or

<Menu

. The Job Menu is displayed. Press

Menu>

or

<Menu

until Reset Printer appears on the second line. Press

Select

.

53 Unformatted Flash

The flash memory installed in your printer has not been formatted. You must

format the flash memory before downloading resources.

Press

Go

to clear the message. To format flash memory, select Format Flash from

the Utilities Menu.

54 Serial Option

x

Error

The printer has detected a protocol error on the specified serial interface. Make

sure the serial interface parameters are set up correctly and you are using an

appropriate serial cable.

•

Press

Go

to clear the message and continue printing. The job may not print

correctly.

•

Reset the printer. Press

Menu>

or

<Menu

. The Job Menu is displayed. Press

Menu>

or

<Menu

until Reset Printer appears on the second line. Press

Select

.

54 Serial

x

Fax Connection Lost

The printer has detected the external modem that was once connected to the

serial port is no longer responding. If the printer has been configured to receive

faxes from a serial port and the Fax Port setting is not set to disabled, it will poll the

modem. If it detects the modem connection is missing, it displays the attendance

message. If the modem connection is re-established, the printer removes the

message from the display.

If the modem has been intentionally disconnected, you can press

Go

to clear the

message and continue printing.

54 Std Par ENA

Connection Lost

An External Network Adapter (ENA) that was once connected to the standard

parallel port is no longer responding. The printer only recognizes the missing

connection when the printer power is first turned on.

•

Make sure the cable connecting the ENA and the printer is securely attached.

Turn the printer off and then on again to see if the printer recognizes the

connection.

•

Press

Go

to clear the message. The printer erases any reference to the ENA

and then resets.

54 Network x Software Error

The printer software has detected that a network port is installed and cannot

establish communications with it.

Press Go to clear the message. The printer disables all communications to the

associated network interface. No data can be transmitted through this interface.

You can program new firmware in the network interface through the parallel port

after this message has been cleared.

Attendance messages (continued)

Message

Action

Section	Page
Table of contents	3
Using your documentation ix	3
Trademarks xiii	3
1 Introducing your printer 1	3
2 Using printer drivers 5	3
3 Changing printer settings 7	3
4 Using color 75	4
5 Managing memory 89	5
6 Handling paper 95	5
7 Replacing supplies 113	6
8 Solving printer problems 145	6
Appendix A: MarkVision 189	7
Appendix B: Printer specifications 201	7
Appendix C: Fonts 205	7
Appendix D: Safety information 215	7
Appendix E: Notices 227	7
Appendix F: Warranty 239	8
Glossary 241	8
Index 255	8
Using your documentation	9
About the manuals	9
Other sources ofinformation	11
Trademarks	13
Introducing your printer	15
Print speed	16
Memory	16
Color quality	16
Printer drivers	17
MarkVision	17
Paper handling	17
Using printer drivers	19
Changing printer settings	21
Using the operator panel	22
Menus	24
Using color	89
Understanding color	89
Managing color	92
Controlling your printer	94
Color Correction	98
Avoiding print quality problems	100
Managing memory	103
Printer memory	103
Adding memory	104
Flash memory	106
Hard disk	106
Managing resources downloaded to flash or disk	107
Handling paper	109
Paper sources and output bins	109
Paper sizes	110
Media guidelines	112
Storing media	118
Avoiding paperjams	118
Loading paper inthe trays	119
Tray linking	123
Using the multipurpose feeder	124
Replacing supplies	127
Ordering supplies	127
Storing supplies	129
When to replacesupplies	130
Recycling usedsupplies	133
Conserving supplies	133
Replacing supplyitems	134
Replacing print cartridges	135
Replacing the coating roll	140
Replacing the fuser kit	145
Replacing the transfer kit	152
Solving printer problems	159
Printer problems	159
Theory of operation	160
Understanding printer messages	161
Identifying other problems	175
Clearing printer paperjams	182
Clearing duplex unit paperjams	189
Cleaning the print cartridge dust collector	195
Cleaning the waste toner sensor	198
Calling for customer support	202
MarkVision	203
Operating systems supported	203
Introducing MarkVision	204
Installing MarkVision on a network	212
Getting updated utilities and drivers	213
Printer specifications	215
Fonts	219
Printing font samples	219
Resident fonts	220
Symbol Sets	225
Downloadable fonts	227
Safety information	229
Notices	241
Laser notices	245
Warranty	253
Glossary	255
A	255
B	256
C	256
D	257
E	258
F	259
G	259
H	260
I	260
J	260
K	260
L	261
M	261
N	262
O	262
P	263
R	265
S	265
T	267
U	267
V	267
Y	268

Lexmark Optra C710 User's Guide - Page 168

Network x Software Error, Std Par ENA

Page 168 highlights