LiftMaster 8010 8010 Owner s Manual - Page 17

Wire the door control to the garage door opener, 12 Attach the warning labels

Get LiftMaster 8010 PDF manuals and user guides View all LiftMaster 8010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Installation 11 Wire the door control to the garage door opener HARDWARE Insulated Staple (Not Shown) 1. Run the white and red/white wire from the door control to the garage door opener. Attach the wire to the wall and ceiling with the staples (not applicable for gang box or pre-wired installations). Do not pierce the wire with the staple as this may cause a short or an open circuit. 2. Strip 7/16 inch (11 mm) of insulation from the end of the wire near the garage door opener. 3. Connect the wire to the red and white terminals on the garage door opener. If your garage is prewired make sure you use the same wires that are connected to the door control. To insert or release wires from the terminal, push in the tab with screwdriver tip. 1 2 7/16" (11 mm) 12 Attach the warning labels 1. Attach the entrapment warning label on the wall near the door control with tacks or staples. 2. Attach the manual release/safety reverse test label in a visible location on the inside of the garage door. Staple 3 RED WHITE WHITE GREY 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
17
Installation
11 Wire the door control to the garage door opener
HARDWARE
Insulated Staple
(Not Shown)
1.
Run the white and red/white wire from the door control to the garage door opener. Attach the
wire to the wall and ceiling with the staples (not applicable for gang box or pre-wired
installations). Do not pierce the wire with the staple as this may cause a short or an open
circuit.
2.
Strip 7/16 inch (11 mm) of insulation from the end of the wire near the garage door opener.
3.
Connect the wire to the red and white terminals on the garage door opener. If your garage is
prewired make sure you use the same wires that are connected to the door control. To insert
or release wires from the terminal, push in the tab with screwdriver tip.
Staple
RED
WHITE
WHITE
GREY
7/16" (11 mm)
2
3
1
12 Attach the warning labels
1.
Attach the entrapment warning label on the wall near the door control with tacks or staples.
2.
Attach the manual release/safety reverse test label in a visible location on the inside of the
garage door.