LiftMaster 8010 8010 Owner s Manual - Page 6

Assembly, 1 Attach the Rail to the Garage Door Opener

Get LiftMaster 8010 PDF manuals and user guides View all LiftMaster 8010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Assembly 1 Attach the Rail to the Garage Door Opener To avoid SERIOUS damage to garage door opener, use ONLY the 1/4"-20x1-3/4" self-threading screws provided. To avoid installation difficulties, do not run the garage door opener until instructed to do so. 1. Place the motor unit on packing material to protect the cover, and rest the back end of the rail on top. For convenience, put a support under the front end of the rail. 2. Ensure that the chain spreader is installed. 3. Place the rail onto the motor unit. Loop the chain around the sprocket. The sprocket teeth must engage the chain. 4. Align the screw holes in the rail with the holes on top of the motor unit. Use a 1/4" socket to fasten the rail with the screws. 5. Attach the outer trolley to the rail and then slide into place over the inner trolley. HARDWARE Inner Trolley Rail Tab Self-Threading Screw 1/4"-20x1-3/4" Outer Trolley IMPORTANT: Use ONLY the 1/4"-20x1-3/4" self-threading screws provided in a separate bag inside the hardware bag. Sprocket Chain spreader Packing Material 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
6
Assembly
1 Attach the Rail to the Garage Door Opener
To avoid SERIOUS damage to garage door opener, use ONLY the 1/4"-20x1-3/4" self-threading
screws provided.
To avoid installation difficulties, do not run the garage door opener until instructed to do so.
1.
Place the motor unit on packing material to protect the cover, and rest the back end of the rail
on top. For convenience, put a support under the front end of the rail.
2.
Ensure that the chain spreader is installed.
3.
Place the rail onto the motor unit. Loop the chain around the sprocket. The sprocket teeth must
engage the chain.
4.
Align the screw holes in the rail with the holes on top of the motor unit. Use a 1/4" socket to
fasten the rail with the screws.
5.
Attach the outer trolley to the rail and then slide into place over the inner trolley.
HARDWARE
Self-Threading Screw
1/4"-20x1-3/4"
IMPORTANT:
Use ONLY
the 1/4"-20x1-3/4"
self-threading screws
provided in a separate bag
inside the hardware bag.
Packing
Material
Rail
Tab
Sprocket
Chain spreader
Outer
Trolley
Inner
Trolley