LiftMaster 8010 8010 Owner s Manual - Page 7

Tighten the Chain

Get LiftMaster 8010 PDF manuals and user guides View all LiftMaster 8010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Assembly 2 Tighten the Chain 1. Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley. 2. To tighten the chain, turn the outer nut in the direction shown. 3. When the chain is approximately 1/4" (6 mm) above the base of the rail at it's midpoint, re- tighten the inner nut to secure the adjustment. Sprocket noise can result if the chain is too loose or too tight. When installation is complete, you may notice some chain droop with the door closed. This is normal. If the chain returns to the position shown when the door is open, do not re-adjust the chain. NOTE: During future maintenance, ALWAYS pull the emergency release handle to disconnect the trolley before adjusting the chain. You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section. To Tighten Outer Nut Trolley Outer Lock Threaded Nut Washer Shaft Inner Nut To Tighten Inner Nut Chain Base of Rail 1/4" (6 mm) Mid length of Rail 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
7
Assembly
2 Tighten the Chain
1.
Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley.
2.
To tighten the chain, turn the outer nut in the direction shown.
3.
When the chain is approximately 1/4" (6 mm) above the base of the rail at it's midpoint, re-
tighten the inner nut to secure the adjustment.
Sprocket noise can result if the chain is too loose or too tight. When installation is complete, you may
notice some chain droop with the door closed. This is normal. If the chain returns to the position shown
when the door is open, do not re-adjust the chain.
NOTE:
During future maintenance, ALWAYS pull the emergency release handle to disconnect the
trolley before adjusting the chain.
You have now finished assembling your garage door opener. Please read the following warnings
before proceeding to the installation section.
Base of Rail
Mid length of Rail
Chain
1/4" (6 mm)
Outer
Nut
Lock
Washer
Trolley
Threaded
Shaft
Inner Nut
To Tighten
Inner Nut
To Tighten Outer Nut