LiftMaster 8160W Owners Manual - Page 15

Install the Light Bulbs for Models 8160W, 8160WB, Install the Light Bulbs for Models 8155W, 8164W

Get LiftMaster 8160W PDF manuals and user guides View all LiftMaster 8160W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Installation 6 Install the Light Bulbs for Models 8160W, 8160WB Install the Light Bulbs for Models 8155W, 8164W and 8165W To prevent possible OVERHEATING of the end panel or light socket: l Use ONLY A19 incandescent (100W maximum) or compact fluorescent (26W maximum) light bulbs. l DO NOT use incandescent bulbs larger than 100W. l DO NOT use compact fluorescent light bulbs larger than 26W (100W equivalent). l DO NOT use halogen bulbs. l DO NOT use short neck or specialty light bulbs. 1. Pull on the top center of the light lens and rotate the light lens down. 2. Insert an A19 incandescent (100W maximum) or compact fluorescent (26W, 100W equivalent) light bulb into the light socket. NOTE: DO NOT use halogen, short neck, or specialty light bulbs as these may overheat the end panel or light socket. DO NOT use LED bulbs as they may reduce the range or performance of your remote control(s). 3. Rotate the lens up to close. or To prevent possible OVERHEATING of the end panel or light socket: l Use ONLY A19 incandescent (100W maximum) or compact fluorescent (26W maximum) light bulbs. l DO NOT use incandescent bulbs larger than 100W. l DO NOT use compact fluorescent light bulbs larger than 26W (100W equivalent). l DO NOT use halogen bulbs. l DO NOT use short neck or specialty light bulbs. 1. Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. 2. Install a 100 watt maximum light bulb in each socket. Light bulb size should be A19, standard neck only. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF. 3. Reverse the procedure to close the lens. NOTE: If the bulbs burn out prematurely due to vibration, replace with A19, standard neck garage door opener bulbs. The use of short neck or specialty light bulbs may overheat the endpanel or light socket. 100 Watt (Max) Standard Light Bulb Release Tab Lens Hinge 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
15
Installation
6 Install the Light Bulbs for Models 8160W, 8160WB
To prevent possible OVERHEATING of the end panel or light socket:
l
Use ONLY A19 incandescent (100W maximum) or compact fluorescent (26W
maximum) light bulbs.
l
DO NOT use incandescent bulbs larger than 100W.
l
DO NOT use compact fluorescent light bulbs larger than 26W (100W
equivalent).
l
DO NOT use halogen bulbs.
l
DO NOT use short neck or specialty light bulbs.
1.
Pull on the top center of the light lens and rotate the light lens down.
2.
Insert an A19 incandescent (100W maximum) or compact fluorescent (26W,
100W equivalent) light bulb into the light socket.
NOTE:
DO NOT use halogen, short neck, or specialty light bulbs as these may overheat
the end panel or light socket. DO NOT use LED bulbs as they may reduce the range or
performance of your remote control(s).
3.
Rotate the lens up to close.
or
Install the Light Bulbs for Models 8155W, 8164W and 8165W
To prevent possible OVERHEATING of the end panel or light socket:
l
Use ONLY A19 incandescent (100W maximum) or compact fluorescent (26W
maximum) light bulbs.
l
DO NOT use incandescent bulbs larger than 100W.
l
DO NOT use compact fluorescent light bulbs larger than 26W (100W
equivalent).
l
DO NOT use halogen bulbs.
l
DO NOT use short neck or specialty light bulbs.
1.
Press the release tabs on both sides of lens. Gently rotate lens back and
downward until the lens hinge is in the fully open position. Do not remove the
lens.
2.
Install a 100 watt maximum light bulb in each socket. Light bulb size should be
A19, standard neck only. The lights will turn ON and remain lit for approximately
4-1/2 minutes when power is connected. Then the lights will turn OFF.
3.
Reverse the procedure to close the lens.
NOTE:
If the bulbs burn out prematurely due to vibration, replace with A19, standard
neck garage door opener bulbs. The use of short neck or specialty light bulbs may
overheat the endpanel or light socket.
100 Watt (Max)
Standard Light Bulb
Release Tab
Lens Hinge