LiftMaster 8160W Owners Manual - Page 39

Control Panel Setup, LIGHT, LIGHT FEATURE Default is Active, MAINTENANCE ALERT SYSTEM MAS

Get LiftMaster 8160W PDF manuals and user guides View all LiftMaster 8160W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Operation Control Panel Setup LOCK Your remote controls will NOT work when LOCK mode is active however your keyless entry will still allow access to your garage. Activate: Press and hold the LOCK button for 2 seconds. The command LED will flash as long as the lock feature is activated and your handheld remote control will not operate your door at this time. Deactivate: Press and hold the LOCK button again for 2 seconds. The command LED will stop flashing and normal operation will resume. Command LED LOCK Button LIGHT To change the amount of time the garage door opener lights will stay on: Press and hold the LOCK button until the garage door opener lights flash.* The time interval is indicated by the number of flashes. Number of times garage door opener lights flash 1 2 3 4 Time the garage door opener light stays on 1-1/2 Minutes 2-1/2 Minutes 3-1/2 Minutes 4-1/2 Minutes To cycle through the time intervals repeat the step above. * Approximately 10 seconds LIGHT FEATURE (Default is Active) Deactivate: Press and hold the LIGHT button until the garage door opener lights turn on, then off again.* Activate: Start with the garage door opener lights on. Press and hold the LIGHT button until the garage door opener lights turn off, then on again.* If the command LED is continuously blinking, the LOCK feature needs to be deactivated. MAINTENANCE ALERT SYSTEM (MAS): Activate/Deactivate: Press and hold the LEARN button. Then press the LIGHT button. The service LED will flash the status; Active is 2 flashes and deactivated is 3 flashes. LOCK Button LIGHT Button Service LED LEARN Button LIGHT Button Command LED 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
39
Operation
Control Panel Setup
LOCK
Your remote controls will NOT work when
LOCK mode is active however your keyless
entry will still allow access to your garage.
Activate:
Press and hold the LOCK button for 2
seconds. The command LED will flash as
long as the lock feature is activated and
your handheld remote control will not
operate your door at this time.
Deactivate:
Press and hold the LOCK button again for 2
seconds. The command LED will stop
flashing and normal operation will resume.
LOCK Button
Command LED
LIGHT
To change the amount of time the garage door opener lights will stay on:
Press and hold the LOCK button until the garage door opener lights flash.* The time
interval is indicated by the number of flashes.
Number of times garage door
opener lights flash
Time the garage door opener light stays on
1
1-1/2 Minutes
2
2-1/2 Minutes
3
3-1/2 Minutes
4
4-1/2 Minutes
To cycle through the time intervals repeat the step above.
* Approximately 10 seconds
LIGHT FEATURE (Default is Active)
Deactivate:
Press and hold the LIGHT button until the
garage door opener lights turn on, then off
again.*
Activate:
Start with the garage door opener lights on.
Press and hold the LIGHT button until the
garage door opener lights turn off, then on
again.*
If the command LED is continuously
blinking, the LOCK feature needs to be
deactivated.
LOCK Button
LIGHT Button
Command LED
MAINTENANCE ALERT SYSTEM (MAS):
Activate/Deactivate:
Press and hold the LEARN button. Then
press the LIGHT button. The service LED
will flash the status; Active is 2 flashes and
deactivated is 3 flashes.
LEARN
Button
LIGHT
Button
Service
LED