LiftMaster HCTDCU HCTDCU Installation Manual - Page 31
Auxiliary Relays, Red/green Light Functionality
View all LiftMaster HCTDCU manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 31 highlights
EXPANSION BOARD AUXILIARY RELAYS AUX RELAY 1 AND 2 Normally Open (N.O.) and Normally Closed (N.C.) relay contacts to control external devices, for connection of Class 2, low voltage (42 Vdc [34 Vac] max 5 Amps) power sources only. Function of relay contact activation determined by switch settings. AUX RELAY SETTING SWITCH SETTINGS 123 AUX RELAY 1 AUX RELAY 2 Off (no feature OFF OFF OFF selected) Relay always off. Use this Aux Relay setting to conserve battery power. Open Limit Switch OFF OFF ON Energizes at open limit. Use with SAMS (Sequenced Access Management System, jointly with barrier gate). Close Limit Switch OFF ON OFF Energizes when not at close limit. For an additional audible or visual display, connect an external light (low voltage). Gate/door Motion OFF ON ON Energizes when motor is on (gate/door in motion). For an additional audible or visual display, connect an external buzzer or light (low voltage). Pre-Motion Delay ON OFF OFF Energizes 3 seconds before gate/door motion and remains energized during gate/door motion. The onboard alarm will sound. For an additional audible or visual display, connect an external buzzer or light (low voltage). Energizes 3 seconds before gate/door motion and remains energized during gate/door motion. For an additional audible or visual display, connect an external buzzer or light (low voltage). Power ON ON OFF Energizes when AC power or solar power is present. There is approximately a 10-12 second delay before relay cutoff, after AC shutdown. Energizes when on battery power. There is approximately a 10-12 second delay before relay cutoff, after AC shutdown. Tamper ON OFF ON Energizes if gate/door is manually tampered with by being pushed Energizes if gate/door is manually tampered with by being off of close limit. For an additional audible or visual display, pushed off of close limit. For an additional audible or visual connect an external buzzer or light (low voltage). display, connect an external buzzer or light (low voltage). Cycle Quantity ON ON ON The 1, 2, and 3 LEDs will blink out the cycle count (cycle count is Feedback* stored on the control board). See below. Red/green light functionality, see below. CYCLE COUNT * First, note the current Aux Relay switch positions. To determine the actual cycles that the gate/door operator has run (in thousands), set all three Aux Relay switches to the ON setting for Aux Relay 1. The Expansion Board's 1, 2, and 3 LEDs will blink out the cycle count, with 1 LED blinking 1000's, 2 LED blinking 10,000's, 3 LED blinking 100,000's, and simultaneously all three LED's blink 1,000,000's (e.g. 1 LED blinks 3 times, 2 LED blinks 6 times, and 3 LED blinks once. Cycle count is 163,000.). Cycle count displayed is between 1,000 and 9,999,000 cycles. After servicing, set Aux Relay switches back to their appropriate positions. Cycle count cannot be reset or changed. If under 1,000 cycles the 1, 2, and 3 LEDs will turn on for 10 seconds, then turn off. NOTE: The expansion board will flash the cycle count 3 times then all the LEDs will turn on solid for 10 seconds then turn off. POWER TO MAIN BOARD SSHHAADDOW IINNTTEERRRUPPTT EEXXITIT OPEN CLOSE 1 EYE ONLY 2 EYE/ EDGE 3 EYE/ EDGE COM SBC OPN CLS STP COM RED/GREEN LIGHT FUNCTIONALITY Red light wired to AUX RELAY 1. Green light wired to AUX RELAY 2. Gate/door STATE AUX RELAY 1 SWITCHES 1 OFF 2 OFF 3 OFF AUX RELAY 2 SWITCHES 1 ON 2 ON 3 ON Closed Red light OFF* Green light OFF Opening Red light ON/Flash Green light OFF Open Red light OFF Green light ON Closing Red light ON/Flash Green light OFF Defined Mid Stop n/a n/a Undefined Mid Stop Red light ON Green light OFF Timer more than 5 seconds Red light OFF Green light ON Timer less than 5 seconds Red light ON/Flash Green light OFF * For red light ON when gate/door is closed, set switch 1 on AUX RELAY 1 to ON AAUUXXRILELIAAYRWYIRRIENLGAEYXAWMPIRLEING EXAMPLE N.C. Aux Relay COM N.O. Class 2 Power Source (42 Vdc [34 Vac], + _ 5 A max) AUX Relay 2 N.C. Com AUX Relay 2 N.O. AUX Relay 1 N.C. Com AUX Relay 1 N.O. Warning Light AUX RELAY 1 AUX RELAY 2 31