LiftMaster LMSC1000 Installation Manual - English French Spanish - Page 5

Wiegand Interface Module Programming, Beeper Enable/Disable, Antenna Range Adjustment

Get LiftMaster LMSC1000 PDF manuals and user guides View all LiftMaster LMSC1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Wiegand Interface Module Programming Power Serial Wiegand RESET Loop PWR RF PWR SET LP SET/ERR SER I SER 0 WO SETUP 6 DC LOOP 5 8SEC 4 4SEC 3 2SEC 2 1SEC 1 ON - OFF Dry Cont SETUP 6 LOOP 5 8SEC 4 4SEC 3 2SEC 2 1SEC 1 ON - OFF Wiegand Retransmission Delay The S2W Wiegand Interface Module has an adjustable Wiegand output retransmission delay from 0-15 seconds. When enabled, the S2W Wiegand Interface will transmit 1 Wiegand pulse and start the timer. If a tag remains in the active reading zone, the S2W Wiegand Interface will not transmit another pulse until the timer expires. The delay is set using the bottom 4 dip-switches shown above. When the switch is set to the left it is in the "On" position. Use the chart to the right to select the desired amount of retransmission delay (in seconds). The default setting is 3 seconds delay. NOTE: The power to the S2W Wiegand Interface must be cycled for any switch changes to take effect. Antenna Range Adjustment The S2W Wiegand Interface Module has an antenna range adjustment located on the circuit board just left of the LED Display. To adjust the range perform the following steps: 1. Place the module in programming mode by setting switch 6 to "On"(left). 2. Locate the adjustment pot and turn clockwise to increase range or counter-clockwise to decrease range. The LED display will show the relative power setting (Max is all LEDs on). 3. To send the new range setting to the reader press the Reset button just above the range adjustment. 4. Once the desired range is set, place the module into operating mode by setting switch 6 (Setup) to "Off" (right). 1 2 3 4 Delay (Seconds) Off Off Off Off 0 On Off Off Off 1 Off On Off Off 2 On On Off Off 3 Off Off On Off 4 On Off On Off 5 Off On On Off 6 On On On Off 7 Off Off Off On 8 On Off Off On 9 Off On Off On 10 On On Off On 11 Off Off On On 12 On Off On On 13 Off On On On 14 On On On On 15 Power RESET Loop Serial Wiegand PWR RF PWR SET LP SET/ERR SER I SER 0 WO DC SETUP 6 LOOP 5 8SEC 4 4SEC 3 2SEC 2 1SEC 1 ON - OFF Dry Cont Beeper Enable/Disable By default, the LMSC1000 will beep when it reads an RFID tag. To toggle this feature (turn on or off) perform the following steps: 1. Place the module in programming mode by setting switch 6 (Setup) to "On" (left). 2. Turn the adjustment pot counter-clockwise to the minimum setting. 3. Press the Reset button just above the range adjustment to toggle the setting. 4. Return the antenna range setting to its original position. 5. Press the Reset button just above the range adjustment to set range. 6. Place the module into operating mode by setting switch 6 to "Off" (right). 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
5
Wiegand Interface Module Programming
Wiegand Retransmission Delay
The S2W Wiegand Interface Module has an adjustable Wiegand output
retransmission delay from 0-15 seconds. When enabled, the S2W Wiegand
Interface will transmit 1 Wiegand pulse and start the timer. If a tag remains
in the active reading zone, the S2W Wiegand Interface will not transmit
another pulse until the timer expires. The delay is set using the bottom
4 dip-switches shown above. When the switch is set to the left it is in the
“On” position. Use the chart to the right to select the desired amount of
retransmission delay (in seconds). The default setting is 3 seconds delay.
NOTE:
The power to the S2W Wiegand Interface must be cycled for any
switch changes to take effect.
1
2
3
4
Delay
(Seconds)
Off
Off
Off
Off
0
On
Off
Off
Off
1
Off
On
Off
Off
2
On
On
Off
Off
3
Off
Off
On
Off
4
On
Off
On
Off
5
Off
On
On
Off
6
On
On
On
Off
7
Off
Off
Off
On
8
On
Off
Off
On
9
Off
On
Off
On
10
On
On
Off
On
11
Off
Off
On
On
12
On
Off
On
On
13
Off
On
On
On
14
On
On
On
On
15
RF
LP
PWR
RESET
Serial
Power
Loop
Dry Cont
Wiegand
SET/ERR
SER I
SER 0
WO
DC
SETUP
LOOP
8SEC
4SEC
2SEC
1SEC
1
2
3
4
5
6
PWR
SET
SETUP
LOOP
8SEC
4SEC
2SEC
1SEC
1
2
3
4
5
6
ON - OFF
ON - OFF
Beeper Enable/Disable
By default, the LMSC1000 will beep when it reads an RFID tag. To toggle this
feature (turn on or off) perform the following steps:
1. Place the module in programming mode by setting switch 6 (Setup) to “On”
(left).
2. Turn the adjustment pot counter-clockwise to the minimum setting.
3. Press the Reset button just above the range adjustment to toggle the setting.
4. Return the antenna range setting to its original position.
5. Press the Reset button just above the range adjustment to set range.
6. Place the module into operating mode by setting switch 6 to “Off” (right).
RF
LP
PWR
RESET
Serial
Power
Loop
Dry Cont
Wiegand
SET/ERR
SER I
SER 0
WO
DC
SETUP
LOOP
8SEC
4SEC
2SEC
1SEC
ON - OFF
1
2
3
4
5
6
PWR
SET
Antenna Range Adjustment
The S2W Wiegand Interface Module has an antenna range adjustment
located on the circuit board just left of the LED Display. To adjust the range
perform the following steps:
1. Place the module in programming mode by setting switch 6 to “On”(left).
2. Locate the adjustment pot and turn clockwise to increase range or
counter-clockwise to decrease range. The LED display will show the
relative power setting (Max is all LEDs on).
3. To send the new range setting to the reader press the Reset button just
above the range adjustment.
4. Once the desired range is set, place the module into operating mode by
setting switch 6 (Setup) to “Off” (right).