MSI 790GX User Guide - Page 61

MemClk Tristate C3/ATLVID

Get MSI 790GX PDF manuals and user guides View all MSI 790GX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

MS-7576 Mainboard DRAM Drive Strength This feature allows you to control the memory data bus' signal strength. Increasing the drive strength of the memory bus can increase stability during overclocking. DRAM Controller Selection This feature allows you to select the DRAM controller. 1T/2T Memory Timing This item controls the SDRAM command rate. Select [1T] makes SDRAM signal controller to run at 1T (T=clock cycles) rate. Selecting [2T] makes SDRAM signal controller run at 2T rate. DCT Unganged Mode This feature is used to Integrate two 64-bit DCTs into a 128-bit interface. Bank Interleaving Bank Interleaving is an important parameter for improving overclocking capability of memory. It allows system to access multiple banks simultaneously. Power Down Enable This is a memory power-saving technology. W hen the system does not access memory over a period of time, it will automatically reduce the memory power supply. MemClk Tristate C3/ATLVID This setting allows you to enable/disable the MemClk Tristating during C3 and ATLVID. FSB/DRAM Ratio This item allows you to select the FSB/DRAM ratio. Adjusted DRAM Frequency (MHz) It shows the adjusted Memory frequency. Read-only. Onboard VGA Over Clock This item allows you to overclock the onboard VGA. Onboard VGA Clock This item will appear when Onboard VGA Over Clock sets to [Enabled]. It allows you to adjust the onboard VGA clock. HT Link Control Press to enter the sub-menu and the following screen appears. 3-22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
MS-7576 Mainboard
3-22
DRAM Drive Strength
This feature allows you to control the memory data bus' signal strength. Increasing
the drive strength of the memory bus can increase stability during overclocking.
DRAM Controller Selection
This feature allows you to select the DRAM controller.
1T/2T Memory Timing
This item controls the SDRAM command rate. Select [1T] makes SDRAM signal
controller to run at 1T (T=clock cycles) rate. Selecting [2T] makes SDRAM signal
controller run at 2T rate.
DCT Unganged Mode
This feature is used to Integrate two 64-bit DCTs into a 128-bit interface.
Bank Interleaving
Bank Interleaving is an important parameter for improving overclocking capability
of memory. It allows system to access multiple banks simultaneously.
Power Down Enable
This is a memory power-saving technology. When the system does not access
memory over a period of time, it will automatically reduce the memory power
supply.
MemClk Tristate C3/ATLVID
This setting allows you to enable/disable the MemClk Tristating during C3 and
ATLVID.
FSB/DRAM Ratio
This item allows you to select the FSB/DRAM ratio.
Adjusted DRAM Frequency (MHz)
It shows the adjusted Memory frequency. Read-only.
Onboard VGA Over Clock
This item allows you to overclock the onboard VGA.
Onboard VGA Clock
This item will appear when Onboard VGA Over Clock sets to [Enabled]. It allows
you to adjust the onboard VGA clock.
HT Link Control
Press <Enter> to enter the sub-menu and the following screen appears.