Mackie CFX12.mkII Owner's Manual - Page 15

Master Features

Page 15 highlights

MASTER SECTION FEATURES We hope you've understood, if not memorized, the CHANNEL STRIP FEATURES you just read. If you're still confused, please look them over again before you tackle this section. Don't worry, it's easy to swallow as long as you take it a bite at a time. MAIN MIX FADER As the name implies, this stereo fader controls the levels of signals sent to the main outputs: XLR and TRS MAIN OUT . The TAPE OUTPUT RCA jacks also receive the main mix, but before the MAIN MIX Fader. Signals feeding the MAIN MIX Fader, after passing through the STEREO GRAPHIC EQ , include: SUB ASSIGN , MAIN INSERT , STEREO EFX RETURN 1 and 2 (including the EMAC EFFECTS PROCESSOR ), and TAPE INPUT . All assigned SUB Faders and EFX RETURNs that are not turned fully down will appear in the MAIN MIX. The fader, set fully up, provides 10 dB of gain. A "U" unity gain point is just below that. When set fully down, the main mix is effectively muted. This is the fader to pull down at the end of the song when you want The Great Fade-Out. METERS The CFX mixer's peak metering system is made up of two columns of twelve LEDs each, with thresholds ranging from -30 dB up to "CLIP" (+22 dBu at the TRS MAIN OUT , +28 dBu at the XLR MAIN OUT). The meters display the main mix, post MAIN MIX Fader , unless a SOLO PFL switch is engaged. When a SOLO PFL switch is engaged, the meters will instead display the solo information, at unity gain (pre channel fader ). Why, you ask? The meters, being a tool for the engineer, must display what the engineer is listening to via the PHONES output. You can get a good mix with the meter's peaks flashing anywhere between -20 and +10 dB. Most amplifiers clip at about +10 dB, and some recorders aren't so forgiving either. For best real-world results, try to keep your peaks between "0" and "+7." You may already be familiar with "+4" (+4 dBu=1.23V) and "-10" (-10 dBV=0.32V) operating levels. Basically, what determines the operating level is the relative 0 dB VU (or 0VU) chosen for the meters. A "+4" mixer, with a +4 dBu signal pouring out the back, will actually display 0 dB on its meters. A "-10" mixer, with a -10 dBV signal trickling out, will also display 0 dB. So ... when is 0 dB actually 0 dB? Right now! At the risk of creating another standard, Mackie's compact mixers address the need of both crowds by calling things as they are: 0 dBu (0.775V) at the output shows as 0 dB VU on the meters. What could be easier? (By the way, the most wonderful thing about standards is that there are so many to choose from.) RUDE SOLO This infamous flashing LED (Light Emitting Diode) serves two purposes -- to remind you that at least one SOLO PFL switch is engaged, and to let you know that you're mixing on a Mackie. Engaging a SOLO PFL switch affects these features: PHONES and Meters . No other outputs are affected in any way. Although the "SET THE LEVELS" section of "QUICK START" (page 5) will get your levelsetting tasks accomplished, using the meters in PFL SOLO mode lets you really tune in. Instead of one flickering LED, you can make use of the 12-segment VU display in the meters. How? Just engage a SOLO PFL switch and watch the meters. WARNING: SOLO is prefader and taps the channel signal before the fader . If you have a channel's fader set well below "U" (unity gain), SOLO won't know that and will send a unity gain signal to the PHONES output. That may result in a startling level boost in your headphones. STEREO GRAPHIC EQ This equalizer, used to shape the frequency spectrum of the main mix, is the last thing in the chain prior to the MAIN MIX Fader and MAIN OUT XLR and TRS jacks. Although there is no actual bypass switch for the STEREO GRAPHIC EQ, by setting all the sliders to zero (center) you'll effectively remove it from the signal path. How to find and reduce feedback: 1. Set the GRAPHIC EQ sliders to zero (cen- ter). 2. Set the GAIN levels, using the ZERO LEVEL or SOLO PFL . 15 OO 48v POWER STATUS LEFT RIGHT CLIP 22 10 7 4 2 0 2 4 ZERO 7 LEVEL SET 10 20 30 0dB = 0dBu RUDE SOLO SSTTEERREEOO MAIINN MMIIXX dB 10 5 U 5 10 20 30 40 50 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

15
MASTER SECTION FEATURES
CLIP
0dB
=
0dBu
LEFT
RIGHT
ZERO
LEVEL
SET
48v
dB
30
20
10
O
O
40
50
5
5
U
60
10
POWER
STATUS
RUDE
SOLO
22
10
7
4
2
0
2
4
7
10
20
30
STEREO
MAIN MIX
We hope you’ve understood, if not memo-
rized, the CHANNEL STRIP FEATURES you
just read. If you’re still confused, please look
them over again before you tackle this section.
Don’t worry, it’s easy to swallow as long as you
take it a bite at a time.
MAIN MIX FADER
As the name implies, this stereo fader
controls the levels of signals sent to the main
outputs: XLR and TRS
MAIN OUT
. The
TAPE OUTPUT
RCA jacks also receive the
main mix, but before the
MAIN MIX
Fader.
Signals feeding the
MAIN MIX
Fader, after
passing through the
STEREO GRAPHIC EQ
, include:
SUB ASSIGN
,
MAIN INSERT
,
STEREO EFX RETURN 1
and
2
(including
the
EMAC EFFECTS PROCESSOR
), and
TAPE INPUT
. All assigned
SUB
Faders
and
EFX RETURN
s
that are not turned
fully down will appear in the
MAIN MIX
.
The fader, set fully up, provides 10 dB of
gain. A “U” unity gain point is just below that.
When set fully down, the main mix is effectively
muted. This is the fader to pull down at the end
of the song when you want The Great Fade-Out.
METERS
The CFX mixer’s peak metering system is
made up of two columns of twelve LEDs each,
with thresholds ranging from –30 dB up to
“CLIP” (+22 dBu at the TRS
MAIN OUT
,
+28 dBu at the XLR
MAIN OUT
). The meters
display the main mix, post
MAIN MIX
Fader
, unless a
SOLO PFL
switch is engaged.
When a
SOLO PFL
switch is engaged,
the meters will instead display the solo infor-
mation, at unity gain (pre channel fader
).
Why, you ask? The meters, being a tool for the
engineer, must display what the engineer is lis-
tening to via the
PHONES
output.
You can get a good mix with the meter’s
peaks flashing anywhere between –20 and +10
dB. Most amplifiers clip at about +10 dB, and
some recorders aren’t so forgiving either. For
best real-world results, try to keep your peaks
between “0” and “+7.”
You may already be familiar
with “+4” (+4 dBu=1.23V)
and “–10” (–10 dBV=0.32V)
operating levels. Basically,
what determines the oper-
ating level is the relative 0 dB VU (or 0VU)
chosen for the meters.
A “+4” mixer, with a +4 dBu signal pouring
out the back, will actually display 0 dB on its
meters. A “–10” mixer, with a –10 dBV signal
trickling out, will also display 0 dB. So ... when
is 0 dB actually 0 dB? Right now!
At the risk of creating another standard,
Mackie’s compact mixers address the need of
both crowds by calling things as they are: 0 dBu
(0.775V) at the output shows as 0 dB VU on the
meters. What could be easier? (By the way, the
most wonderful thing about standards is that
there are so many to choose from.)
RUDE SOLO
This infamous flashing LED (Light Emitting
Diode) serves two purposes —- to remind you
that at least one
SOLO PFL
switch is en-
gaged, and to let you know that you’re mixing
on a Mackie.
Engaging a
SOLO PFL
switch affects
these features:
PHONES
and Meters
.
No other outputs are affected in any way.
Although the “SET THE LEVELS” section
of “QUICK START” (page 5) will get your level-
setting tasks accomplished, using the meters
in
PFL SOLO
mode lets you really tune in.
Instead of one flickering LED, you can make
use of the 12-segment VU display in the meters.
How? Just engage a
SOLO PFL
switch and
watch the meters.
WARNING:
SOLO
is pre-
fader and taps the channel
signal before the fader
.
If you have a channel’s fad-
er set well below “
U
” (unity
gain),
SOLO
won’t know that and will send a
unity gain signal to the
PHONES
output.
That may result in a startling level boost in
your headphones.
STEREO GRAPHIC EQ
This equalizer, used to shape the frequency
spectrum of the main mix, is the last thing in
the chain prior to the
MAIN MIX
Fader
and
MAIN OUT
XLR and TRS jacks.
Although there is no actual bypass switch
for the
STEREO GRAPHIC EQ
, by setting all
the sliders to zero (center) you’ll effectively
remove it from the signal path.
How to find and reduce feedback:
1.
Set the
GRAPHIC EQ
sliders to zero (cen-
ter).
2.
Set the
GAIN
levels, using the
ZERO
LEVEL
or
SOLO PFL
.