Mackie ProFX12 Owner's Manual - Page 24

R R UNBAL R LINE IN 12 ST RETURN FX SEND MAIN OUT PHONES ProFX8 and ProFX12 STEREO GRAPHIC EQ U 15 10 -20 +20 5 GAIN 0 15 48V 10 PHANTOM 5 POWER 0 5 5 U EQ 10 10 -15 +15 U HI 12kHz -15 +15 U MID 2.5kHz LOW 80Hz -15 +15 U AUX MON +15 U FX +15 PAN 15 125 250 500 1K MAIN MIX MON 2K 4K EQ IN BYPASS 15 8K FX PRESETS 01 BRIGHT ROOM 02 WARM LOUNGE 03 SMALL STAGE 48 04 WARM THEATER 05 WARM HALL 06 CONCERT HALL 07 PLATE REVERB 08 CATHEDRAL 09 CHORUS 49 10 CHORUS + REV 11 DOUBLER PRESETS 12 TAPE SLAP 13 DELAY 1 (300ms) MUTE 14 DELAY 2 (380ms) 52 15 DELAY 3 (480ms) 16 REVERB + DLY (250ms) 50 U U OO USB U +10 INPUT LEVEL USB THRU 51 53 OL POWER MAIN METERS 0dB=0dBu OL 15 10 6 3 0 2 4 7 10 20 30 L R BREAK (MUTES ALL CHANNELS) U OO LR OO +15 +15 OO MAX +20 OO FX MASTER FX TO MON PHONES TAPE LEVEL OO OO OL MUTE 11/12 StOeL SrTeMRUoTTENEffeFcXtsRTPNrocMeOsNsor MAIN dB dB dB dB dB 10 T10he Mackie Ru1n0ning-Man 32-1b0it internal eff1e0 cts 5 pro5cessor is a mo5no-in, stereo-o5ut effects proc5essor, with 16 presets. It is fed by adjusting the aux FX control U [26U] on each chaUnnel. The FX mUaster knob [5U1] adjusts 5 the5overall level e5ntering the FX5 processor and5 the 10 OL1L0 ED [52] show10s if the level 1is0 too high. 10 49. PRESET SELECTOR Rotate this knob to increase or decrease the number of the preset. The available presets are shown in the table on the next page and are marked on the panel silkscreen. (Only one preset may be selected at a time.) 50. INTERNAL FX MUTE and LED When engaged, the internal effects processor is muted. Its output will not appear in the main mix or monitors, and the adjacent LED will come on. The footswitch connection [15] becomes disabled and the footswitch cannot be used to mute or un-mute the effects. If this switch is not engaged, then the internal effects may be muted or un-muted with a footswitch. 51. FX MASTER Use this knob to control the level of t­he signals going into the internal effects processor. Adjust it carefully, with an inner magical eye on the adjacent OL LED [52] to prevent overloading the effects processor. Fully down is off, 12 o'clock is unity gain, and fully up is 15 dB of gain. It also affects the level going out of the FX send output [13]. 52. OL LED This LED illuminates when the effects processor is being overloaded with too strong a signal (OL). Turn down the FX master [51] if it is. 20 T2h0 e output from20 the processo2r0 may be adde2d0 to The signals going into the processor are affected by 30 the30main mix by a3d0 justing the F3X0 return fader30[45]. the channel aux FX controls [26], and the channel 40 Its 4o0utput may als40o be added to4t0he monitor m4i0x by faders [30]. Check the LED if these controls have been 50 60 adj56u00sting the FX t5600o mon knob [556003]. 50 60 altered. OO OO OO OO OO 48. PRESET DISPLAY This display shows the number of the currently selected effects preset, as shown in the list of presets silkscreened to the left of the display. 53. FX TO MON This knob adds the output of the internal FX processor to the stage monitor mix. Fully down is off, 12 o'clock is unity gain, and fully up is 15 dB of gain. 24 ProFX8 and ProFX12