Magnavox MWD2206 Owners Manual - Page 23

Reset to the Default Setting (Except for PARENTAL Setting) 1 PstroePpsLAsmY[oSdEeT. UP] in the SETUP STOP SETUP QUICK CUSTOM INITIALIZE 2 Select "INITIALIZE". or SETUP QUICK CUSTOM INITIALIZE 3 Select "YES". or ENTER SETUP Initialize? NO YES INITIALIZE ENTER 4 To exit the menu SETUP Press twice. Hint • When you cancel to initialize at step , select "NO". Troubleshooting Guide Information If this unit does not perform properly when operated as instructed in this Owner's Manual, check this unit consulting the following checklist. DVD / VCR VCR PROBLEM No power. This unit does not respond to the remote control. Poor picture or noise. Timer recording is impossible. Cannot go into record mode. CORRECTIVE ACTION • Make sure the power plug is connected to an AC outlet. • Make sure the power is turned on. • Check if the power plug is connected to an AC outlet. • Check the batteries in the remote control. • Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote control. • You have to be within 2 feet (7m) of this unit. • Check if the right mode is selected. If it's not in the right mode, press [DVD] or [VCR], whichever you need, on the remote control. • Check if a cassette tape is in this unit. • Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up, then if you hear some signal sound from the radio in response to your pressing buttons on the remote control, the remote control is working. • Interference signal may be received. Change the position and orientation of the unit. • Make sure the Timer Recording is set correctly. • Make sure TIMER REC indicator on the front panel lights up. If not, press [SUBTITLE/T-SET]. • Make sure the VCR clock is set correctly. • Make sure the tape has a record tab. If needed, cover the hole with adhesive tape. • Activate this unit in VCR mode. Press [VCR] on the remote control so that the VCR OUTPUT light is lit. Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing [CHANNELL/K]] on the unit or [SKIP/CH. G/K, H/L] on the remote control. Cannot view a tape but the audio is OK. • Head cleaning may be necessary. Refer to "AUTO HEAD CLEANING". • Make sure the VCR is not in the Menu mode. No or poor, playback picture. • Change the RF output channel to CH4. Then select the same channel on the TV. • Fine tune your TV. TV programs cannot be seen normally. Video or color fades in and out when making a copy of a video tape. • Re-check the ANT-IN and ANT-OUT connections. See the front page and page 6. • Press [VCR]. • Press [VCR] on the remote control to activate it in the VCR mode. Check if the VCR OUTPUT light is lit, then set it to the TV position by press- ing [VCR]. • You cannot copy a copyrighted video tape. You are experiencing copy guard protection. Cannot remove the tape. No picture. Disc cannot be played. No sound. Distorted picture. Audio or subtitle language does not match the setup. • Check if this unit is in the VCR mode. If not, press [VCR] on the remote control to switch the mode. • Connect the video cable firmly. • Insert a correct video disc that plays on this unit. • Press [DVD] on the remote control. Check if the DVD OUTPUT light is lit. Then try other DVD features. • Insert the disc. • Clean the disc. • Place the disc correctly with the label side up. • Cancel the parental lock or change the control levels. • Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on its surface. • Connect the audio cables firmly. • Turn the power of the audio component on. • Correct the audio output settings. • Correct the input settings on the audio component. • Connect this unit directly to the TV. • There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunction. • Although pictures may stop for a moment, this is not a malfunction. • The selected language is not available for audio or subtitles on the DVD. -This is not a malfunction. The camera angle cannot • The DVD does not contain sequences recorded from different camera angles. be changed. -This is not a malfunction. Audio or subtitle language • The DVD does not contain audio source or subtitles in the selected language. cannot be changed. -This is not a malfunction. "Prohibited icon" appears on the screen, prohibiting an operation. • That operation is prohibited by this unit or the disc. -This is not a malfunction. DVD • Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner's Manual for details on correct operations. • Playback from a desired track and random playback are not available during program playback. • Some functions are prohibited on some discs. Information - 2 - EN