Magnavox MWD2206 Owners Manual - Page 27
Quick Use Guide - time recorder changes to dvd
UPC - 053818570036
View all Magnavox MWD2206 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 27 highlights
Quick Use Guide 1 Connections Please refer to "Basic TV Connection" on the front page before you use this unit. RF Output Channel If channel 3 has been already occupied for broadcasting, 1) Set your TV to channel 4. 2) Insert a pre-recorded tape into this unit. 3) Press [SOURCE] on the unit so that the VCR OUTPUT light is lit. • If noise appears on the TV screen, press [VCR/TV] on the remote control. 4) Press [PLAY B] once. 5) After a few seconds, press and hold [PLAY B] on the • unit The for 3 seconds. RF output channel will cha1nge to channel 4 from channel 3 and you will see a playback picture. • When a picture does not appear on the TV screen, repeat step 4. 6) Press [STOP C] t1o stop playba2ck. 2 Installing the Batteries for the Remote Control 11 22 33 3 VC2R/DVD Sw3 itching 3 OPEN/CLOSE CHANNEL VCR DVD SOURCE PREV DISC IN PLAY STOP PLAY NEXT VCR button DVD button VCR DVD SOURCE DVD OUTPUT light SOURCE button VCR OUTPUT light STANDBY-ON SPEED OPEN/CLOSE AUDIO /EJECT 1 2 4 5 7 8 0 DISPLAY VCR 3 SKIP/CH. 6 VCR/TV 9 SLOW +10 DVD PAUSE RECORD PLAY STOP MENU ENTER SETUP TOP MENU RETURN MODE ZOOM SEARCH MODE CLEAR/ C. RESET SUBTITLE T-SET ANGLE REPEAT A-B VCR MODE Press [VCR] on the remote control.(Verify that the VCR OUTPUT light is lit.) DVD MODE Press [DVD] on the remote control.(Verify that the DVD OUTPUT light is lit.) Hint • Pressing only [SOURCE] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control. 4 Turn On the Unit for the First Time VCR 1 Turn on the TV and set it to channel 3. • If channel 3 has been already occupied for broadcasting, see "RF Output Channel" section. 2 Select your language in the first time you turn on this unit. Then press [B] to go to next step. LANGUAGE SELECT STANDBY-ON or B ENGLISH FRANCAIS ESPAÑOL [ON] 3 Press [B] to start Auto Set Up. CH 01 AUTO SET UP Do you connect the cable from the cable box or the satellite box to the unit's ANT-IN jack? YES NO Yes Press [MENU] to exit. No Please wait for a few minutes. After scanning... • The tuner stops on the lowest memorized channel. • You can select only the channels memorized in this unit by using [SKIP/CH. G/K, H/L] (or [CHANNEL K/L]). • If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press [B] once again. 5 Clock Set Up VCR 1 Press [MENU] and select "CLOCK SET". Then press [B] to go to next step. MENU or - M E N U - TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT • If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2. 2 Select the current month. Then press [B] to go to next step. or CLOCK SET MONTH DAY 10 / -- YEAR - - - - HOUR MINUTE AM/PM -- : -- - - 3 Select the current day. Then press [B] to go to next step. or CLOCK SET MONTH DAY 10 / 02 YEAR - - - - HOUR MINUTE AM/PM -- : -- - - 4 Select the current year. Then press [B] to go to next step. or 5 Select the current hour. Then press [B] to go to next step. or CLOCK SET MONTH DAY 10 / 02 YEAR 2 0 0 6 HOUR MINUTE AM/PM -- : -- - - CLOCK SET MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6 HOUR MINUTE AM/PM 05 : -- - - 6 Select the current minute. Then press [B] to go to next step. or 7 Select "AM" or "PM". or 8 To exit the CLOCK SET screen CLOCK SET MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6 HOUR MINUTE AM/PM 05 : 40 - - CLOCK SET MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6 HOUR MINUTE AM/PM 05 : 40 P M AM B PM ✄ - 27 - EN