Makita XNB01Z Makita XNB01 Instruction Manual - Page 8

Operation

Get Makita XNB01Z PDF manuals and user guides View all Makita XNB01Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Hook CAUTION: • Always make sure that your fingers are not placed on the trigger, and the battery cartridge and nails are removed before using the hook. • Do not hang the hook from the waist belt. Dropping the nailer, which is caused by the hook accidentally coming out of place, may cause misfiring and personal injuries. 014587 1. Groove 2. Hook 3. Screw 1 3 2 014588 The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out. Hex wrench storage 1. Hex wrench 1 014589 When not in use, store the hex wrench as shown in the figure to keep it from being lost. OPERATION Inspecting trigger function CAUTION: • Make sure that the trigger function is in working order before each operation. If you find issues described below, ask Makita Authorized Service Centers for repairs. • Before installing the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. The tool must not operate only by pulling the trigger or only by placing the contact element against the work piece. Driving nails CAUTION: • Always be sure to first place the contact element against the workpiece before pulling the trigger. Select the nailing mode by pressing the mode selecting button as mentioned in the section "Nailing mode selection". Intermittent nailing (sequential mode) 1. Place the 2 contact element 1 against workpiece. 2. Pull the trigger 014619 To drive a nail, set the lock button to the "FREE" position. Place the contact element against the workpiece and pull the trigger. Release the trigger after each operation. Continuous/ intermittent nailing (continuous mode) 1. Pull the trigger 1 2. Place the 2 contact element against workpiece. 014620 When the tool is set to continuous mode, you can operate either continuous or intermittent nailing. To drive a nail, set the lock button to the "FREE" position. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
8
Hook
CAUTION:
•
Always make sure that your fingers are not placed
on the trigger, and the battery cartridge and nails
are removed before using the hook.
•
Do not hang the hook from the waist belt.
Dropping the nailer, which is caused by the hook
accidentally coming out of place, may cause
misfiring and personal injuries.
014587
1
2
3
014588
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out.
Hex wrench storage
1
014589
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
OPERATION
Inspecting trigger function
CAUTION:
•
Make sure that the trigger function is in working
order before each operation. If you find issues
described below, ask Makita Authorized Service
Centers for repairs.
•
Before installing the battery cartridge into the tool,
always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released.
The tool must not operate only by pulling the trigger or
only by placing the contact element against the work
piece.
Driving nails
CAUTION:
•
Always be sure to first place the contact element
against the workpiece before pulling the trigger.
Select the nailing mode by pressing the mode selecting
button as mentioned in the section "Nailing mode
selection".
Intermittent nailing (sequential mode)
1
2
014619
To drive a nail, set the lock button to the "FREE"
position. Place the contact element against the
workpiece and pull the trigger. Release the trigger after
each operation.
Continuous/ intermittent nailing (continuous mode)
1
2
014620
When the tool is set to continuous mode, you can
operate either continuous or intermittent nailing.
To drive a nail, set the lock button to the "FREE"
position.
1. Pull the trigger
2. Place the
contact element
against
workpiece.
1. Place the
contact element
against
workpiece.
2. Pull the trigger
1. Hex wrench
1. Groove
2. Hook
3. Screw