Makita XRM11 XRM11 Instruction Manual - Page 8

NOTE: Depending on the conditions of use and the ambient temperature, the indication may differ slightly from the actual capacity. Using supplied AC power adaptor Remove the rubber protector and insert the adaptor plug into the DC socket on the right hand side of the speaker. Plug the adaptor into a standard mains socket outlet. Whenever the adaptor is used, the battery pack is automatically disconnected. CAUTION: ●● Always disconnect the AC power adaptor completely before moving the speaker. If the AC adaptor is not removed, it may cause an electric shock. ●● Never pull and/or drag the cord of the adaptor. If not, the speaker may accidentally fall down, causing injury to you or someone around you. IMPORTANT: ●● The mains adaptor is used as the means of connecting the speaker to the mains supply. The mains socket used for the speaker must remain accessible during normal use. ●● In order to disconnect the speaker, the mains adaptor should be removed from the mains outlet completely. ●● Use the AC power adaptor supplied with the product or specified by Makita only. ●● Do not hold the power supply cable and plug by your mouth. Doing so might cause an electric shock. ●● Do not touch the power plug with wet or greasy hands. ●● Damaged or entangled cords increase the risk of electric shock. If the cord is damaged, have it replaced by our authorized service center in order to avoid a safety hazard. Do not use it before repair. ●● After use, always store AC power adaptor out of the reach of children. If Children play with the cord, they may suffer injury. USB power supply socket This jack can be used to charge a mobile phone or any other device that uses less than 2.1A of DC current. Charging will only occur when the speaker is switched on. NOTE: Ensure the specification of your external device such as mobile phone or player is compatible with the speaker. Please read instruction manual of your external device before charging. IMPORTANT: ●● Before connecting USB device to the charger, always backup your data of USB device. Otherwise your data may lose by any possibility. ●● The charger may not supply power to some USB devices. ●● When not using or after charging, remove the USB cable and close the cover. ●● Do not connect power source to USB port. Otherwise there is risk of fire. The USB port is only intended for charging lower voltage device. Always place the cover onto the USB port when not charging the lower voltage device. ●● Do not insert a nail, wire, etc. into USB power supply port. Otherwise a circuit short may cause smoke and fire. ●● Do not connect this USB socket with your PC USB port, as it is highly possible that it may cause breakdown of the units. LISTENING TO MUSIC VIA BLUETOOTH STREAMING You need to pair your Bluetooth device with the speaker before you can auto-link to play/stream Bluetooth music through the speaker. Pairing creates a 'bond' so two devices can recognize each other. Note: To have the better sound quality, we recommend setting the volume to more than two-thirds level on your Bluetooth device and then adjust the volume on the speaker as required. Pairing your Bluetooth device for the first time 1. Press the Power button to turn on the speaker. "Pairing" will appear on the display to show the speaker is discoverable. 2. Activate Bluetooth on your device according to the device's user manual to link to the speaker. Locate the Bluetooth device list and select the device named "XRM11" (With some mobiles which are equipped with earlier versions than BT2.1 Bluetooth device, you may need to input the pass code "0000"). 3. Once connected, there will be a confirmation tone sound. "Paired" will appear on the display. You can simply select and play any music from your source device. Volume control can be adjusted from your source device, or directly from the speaker. 4. Use the controls on your Bluetooth-enabled device or on the speaker to play/pause and navigate tracks. Note: ●● If 2 Bluetooth devices, pairing for the first time, both search for the speaker, it will show its availability on both devices. However, if one device links with this unit first, then the other Bluetooth device won't find it on the list. ●● If your Bluetooth device is temporarily disconnected to the speaker, then you need to manually reconnect your device again to the speaker. 8 ENGLISH