Makita XRT01TK XRT01 Instruction Manual - Page 17

Error display and error tone

Get Makita XRT01TK PDF manuals and user guides View all Makita XRT01TK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

7. After assembling, confirm that the contact plate can move as shown in the figure. NOTE: If the contact plate is caught, press it as shown in the figure. 1 ► 1 . Contact plate Error display and error tone CAUTION: During inspection, be sure to lock the trigger, turn the power off, and remove the battery cartridge. Failure to do so may cause an accident. CAUTION: When you turn the power on, never bring your limbs or face close to the binding or rotating parts of the tool tip. Otherwise, you may be injured. CAUTION: When the power is turned on, never touch the binding or rotating parts of the tool tip. Otherwise, you may be injured. CAUTION: If an error tone sounds, or if the tool malfunctions, immediately stop using the tool. Error tone and display If an error occurs, an error tone will sound, and an error number will be shown on the display panel. Refer to the following table and take appropriate actions. If the error persists, ask Makita Authorized Service Centers for repairs. Display 1 2 3 4 5 6 7 Symptom The tool stops operating. Possible cause The wire has been used up. Tie wire is not loaded. Wire feeding has failed. The tool stops operating. The curl guide is open. The tool does not perform the tying The contact plate is caught. process in continuous actuation mode. The tool does not start. The tool stops operating. The battery has been discharged. The temperature of the battery cartridge is abnormally high. The tool stops operating. The motor is overloaded. Motor failure The tool stops operating. The tool does not start. The tool stops operating. The temperature of the tool is abnormally high. Tool failure Solution Load new tie wire. Load tie wire. Check the orientation of the tie wire. Unload the tie wire, and load it again. Clean the path of wire. Close the curl guide. Release the contact plate from being caught. Recharge the battery. Cool the battery cartridge down. Replace the battery cartridge with a recharged one. Determine the cause of the obstruction of the motor rotation and solve the problem. Cool the tool down. Ask Makita Authorized Service Centers for repairs. 17 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
17
ENGLISH
7.
After assembling, confirm that the contact plate
can move as shown in the figure.
1
►
1.
Contact plate
NOTE:
If the contact plate is caught, press it as
shown in the figure.
Error display and error tone
CAUTION:
During inspection, be sure to lock the trigger, turn the power off, and remove the battery
cartridge.
Failure to do so may cause an accident.
CAUTION:
When you turn the power on, never bring your limbs or face close to the binding or rotating
parts of the tool tip.
Otherwise, you may be injured.
CAUTION:
When the power is turned on, never touch the binding or rotating parts of the tool tip.
Otherwise, you may be injured.
CAUTION:
If an error tone sounds, or if the tool malfunctions, immediately stop using the tool.
Error tone and display
If an error occurs, an error tone will sound, and an error number will be shown on the display panel. Refer to the
following table and take appropriate actions. If the error persists, ask Makita Authorized Service Centers for repairs.
Display
Symptom
Possible cause
Solution
1
The tool stops operating.
The wire has been used up.
Load new tie wire.
Tie wire is not loaded.
Load tie wire.
Wire feeding has failed.
Check the orientation of the tie wire.
Unload the tie wire, and load it again.
Clean the path of wire.
2
The tool stops operating.
The curl guide is open.
Close the curl guide.
3
The tool does not perform the tying
process in continuous actuation mode.
The contact plate is caught.
Release the contact plate from
being caught.
4
The tool does not start.
The tool stops operating.
The battery has been
discharged.
The temperature of the battery
cartridge is abnormally high.
Recharge the battery.
Cool the battery cartridge down.
Replace the battery cartridge
with a recharged one.
5
The tool stops operating.
The motor is overloaded.
Determine the cause of the
obstruction of the motor rotation
and solve the problem.
Motor failure
6
The tool stops operating.
The temperature of the tool is
abnormally high.
Cool the tool down.
7
The tool does not start.
The tool stops operating.
Tool failure
Ask Makita Authorized Service
Centers for repairs.