Marantz SR5004 SR6004 / SR5004 User Manual - English - Page 78
Sr5004 Remote Controller, Basic Operation
View all Marantz SR5004 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 78 highlights
ENGLISH NAMES AND FUNCTIONS CONNECTIONS BASIC OPERATION ADVANCED CONNECTIONS BASIC ADVANCED OPERATION SR5004 REMOTE CONTROLLER BASIC OPERATION NORMAL MODE (When operating Marantz AV equipment products) This remote controller is preset with a total of 12 types of remote codes, including Marantz BD, DVD, VCR (VCR deck), DSS (Satellite broadcasting tuner), TV (Television), CD, CDR, AUX, TUNER, USB, M-XP and AMP mode. Learning is not necessary for Marantz products. You can use these products without setting any codes. 1. Press the SOURCE button. For this example, press DVD. Pressing the SOURCE button once changes the remote control to the settings for the source that was pressed. To change the amplifier on other source, press the SOURCE button twice (doubleclick). The code is sent, and then the amplifier source changes to DVD. SETTING THE BACK LIGHT Pressing the Light button located on the side of the remote controller lights the remote controller's backlight. Pressing the button again while the backlight is lit lights the backlight for another 2 seconds. To turn off back light, press and hold down the SET and OFF button until SEND indicator blinks twice. To turn on it again, press and hold down the SET and ON button until SEND indicator blinks twice. Initial is back light ON. PRESET MODE (When operating non-Marantz AV equipment products) This remote controller is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, CD, DVD and DSS. Settings can be made in one of two ways. When the preset codes are set, the following codes are contained in the source button of the remote controller. 76 See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings. Remote controller source name TV DVD CD DSS BD Corresponding preset code Device name TV DVD CD SATELLITE BD Television DVD player CD player Satellite broadcasting tuner equipment Blu-ray disc player Importants • Some codes may be not match your equipment. In this case, you can use LEARN mode to store these codes. • The preset codes do not cover full functions. If you need extra function, use LEARN mode to store extra function. • Wen the batteries are getting weak, the preset procedure is not successful. PROGRAMMING WITH THE 4-DIGIT CODE 1. 2. 1. 1. Press and hold down the SOURCE button for the appliance which should be controlled and press SET button until the SEND indicator blinks twice. Then back light flushes. 2. Press the 4-digit code by numeric buttons for appliance (code table at the end of this book) When the procedure is successful, the SEND indicator will blink twice. Note If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again. SCANNING THE CODE TABLE 2. 3. 2. 3. 5. 1. Switch on the appliance which should be controlled. 2. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then back light flushes. 3. Aim the remote control at the appliance and slowly alternate between pressing INPUT 3 button and the SOURCE ON/OFF button for the appliance. 4. Stop when the appliance turns off. 5. Press ENTER button once to lock in the code. CHECKING THE CODE 2. 1. 3. 1. 4. 1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice then back light flushes. 2. Press the INFO button. The SEND indicator will blink twice. 3. To view the code for first digit, press 1 once. Count the SEND indicator blinks (e.g. 3 blinks = 3) and write down the number. 4. Then press 2 to check the second digit of the code. Now press 3 and 4 to check the third and fourth digits of the code. Note If a code digit is "0", the SEND indicator will not blink. RESETTING THE CODE 1. 1. 2. 1. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Then back light flushes. 2. Press the below codes to reset. TV : 1000 DVD : 2000 CD : 3000 DSS : 4000 BD : 5000 The indicator will blink twice. Note After this procedure, the selected SOURCE button is set initial code. SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS