Maytag MHWE500VW Use and Care Guide - Page 11

Secure the Drain Hose, Level the Washer, Complete Installation - 11

Get Maytag MHWE500VW - Performance Series Front Load Washer PDF manuals and user guides
UPC - 883049134642
View all Maytag MHWE500VW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Secure the Drain Hose 1. Drape the power cord over the washer top. 2. Secure the drain hose to the laundry tub leg or standpipe with the beaded strap provided. (See illustrations A and B.) Complete Installation 1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See "Electrical Requirements." 2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 3. Check that you have all of your tools. 4. Dispose of/recycle all packaging materials. 5. Check that the water faucets are on. 6. Check for leaks around faucets and inlet hoses. A B C If the washer faucets and the drain standpipe are recessed (see illustration C), put the hooked end of the drain hose in the standpipe. Tightly wrap the beaded strap around the water inlet hoses and the drain hose. Do not force excess drain hose into the standpipe. Level the Washer Properly leveling your washer avoids excessive noise and vibration. 1. Check the levelness of the washer by placing a level on the top edge of the washer, first side to side, then front to back. If the washer is against a wall, move the washer out slightly before tipping back. If the washer is not level, first prop the front with a wood block and adjust the feet as necessary; then prop the back and adjust feet as necessary. Repeat this step until washer is level. 2. Make sure all four feet are stable and resting on the floor. Then check that the appliance is perfectly level (use a level). 3. After the washer is level, use a 17 mm open-end wrench to turn the nuts on the feet tightly against the washer cabinet. IMPORTANT: All four feet must be tightened. If the nuts are not tight against the washer cabinet, the washer may vibrate. 4. The washer should not move front to back, side to side, or diagonally when pushed on its top edges. 5. Slide the washer to its final location. 6. Confirm the levelness of the washer. 7. Plug into a grounded 3 prong outlet. 8. Read "Washer Use." 9. To test and clean your washer, make sure there are no clothes in the washer and add one AFFRESH™ tablet to the washer drum. Select POWER/CANCEL, the Clean Washer cycle, and then select START/PAUSE. This cycle will take approximately 50 minutes to complete. Allow the washer to complete the entire Clean Washer Cycle without interruption. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
11
Secure the Drain Hose
1.
Drape the power cord over the washer top.
2.
Secure the drain hose to the laundry tub leg or standpipe with the beaded strap provided.
(See illustrations A and B.)
If the washer faucets and the drain standpipe are recessed (see illustration C), put the
hooked end of the drain hose in the standpipe. Tightly wrap the beaded strap around the
water inlet hoses and the drain hose.
Do not force excess drain hose into the standpipe.
Level the Washer
Properly leveling your washer avoids excessive noise and vibration.
1.
Check the levelness of the washer by placing a level on the top edge of the washer, first
side to side, then front to back.
If the washer is against a wall, move the washer out slightly before tipping back. If the
washer is not level, first prop the front with a wood block and adjust the feet as necessary;
then prop the back and adjust feet as necessary. Repeat this step until washer is level.
2.
Make sure all four feet are stable and resting on the floor. Then check that the appliance is
perfectly level (use a level).
3.
After the washer is level, use a 17 mm open-end wrench to turn the nuts on the feet tightly
against the washer cabinet.
IMPORTANT:
All four feet must be tightened. If the nuts are not tight against the washer
cabinet, the washer may vibrate.
4.
The washer should not move front to back, side to side, or diagonally when pushed on its
top edges.
5.
Slide the washer to its final location.
6.
Confirm the levelness of the washer.
Complete Installation
1.
Check the electrical requirements. Be sure that you have the correct electrical supply and
the recommended grounding method. See “Electrical Requirements.”
2.
Check that all parts are now installed. If there is an extra part, go back through the steps to
see which step was skipped.
3.
Check that you have all of your tools.
4.
Dispose of/recycle all packaging materials.
5.
Check that the water faucets are on.
6.
Check for leaks around faucets and inlet hoses.
7.
Plug into a grounded 3 prong outlet.
8.
Read “Washer Use.”
9.
To test and clean your washer, make sure there are no clothes in the washer and add one
AFFRESH™ tablet to the washer drum. Select POWER/CANCEL, the Clean Washer cycle,
and then select START/PAUSE. This cycle will take approximately 50 minutes to
complete. Allow the washer to complete the entire Clean Washer Cycle without
interruption.
A
B
C