Motorola 68230 Operation Guide - Page 26

Steps to Connect to the CTP, Steps to Default Port 3 CTP Configuration

Get Motorola 68230 - Vanguard 300 DSU/CSU PDF manuals and user guides View all Motorola 68230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Steps to Connect to the CTP Use the CTP for initial configuration, reporting, and troubleshooting. Follow these steps to connect to the CTP. Step Action 1 Connect a local PC or terminal to the CTP port (9600 baud, 8 bit characters, 1 stop bit, no parity) on the Vanguard 300/305. 2 For APAD access, enter .ctp and press Return to call the CTP. For ATPAD access, enter ATDS0 3 At the Password prompt, press Return. Result If the APAD option is in your software image, the * prompt appears. If the ATPAD option is in your software image, the OK prompt appears. A call places a mnemonic call to the CTP. A prompt appears to enter the password. The Main menu appears; logon to the CTP is complete. The local terminal functions as a control terminal. See the 6500 Series Introduction Manual for additional information about the CTP. Steps to Default Port 3 CTP Configuration Follow these steps to default Port 3 to 9600 kbps, 8N1. Step Action 1 From the front panel of the unit, set the switch CTP -> Port 3to the Up position. 2 Reset or power cycle the unit. 3 For APAD access, enter .ctp, or for ATPAD access, enter ATDS0, and configure port parameters. 4 Set the CTP -> Port 3 switch to the Down position. Reset or power cycle the unit. 5 Reset or power cycle the unit. 6 Reboot to verify that the configuration in configuration memory is operating. Refer to the 6500 Series Configuration and Administration Manual for additional information about configuration.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Steps to Connect to the CTP
Use the CTP for initial configuration, reporting, and troubleshooting. Follow
these steps to connect to the CTP.
Step
Action
Result
1
Connect a local PC or terminal to
the CTP port (9600 baud, 8 bit
characters, 1 stop bit, no parity) on
the Vanguard 300/305.
If the APAD option is in your
software image, the * prompt
appears. If the ATPAD option is in
your software image, the OK
prompt appears.
2
For APAD access, enter .ctp and
press Return to call the CTP. For
ATPAD access, enter ATDS0
A call places a mnemonic call to
the CTP. A prompt appears to enter
the password.
3
At the Password prompt, press
Return.
The Main menu appears; logon to
the CTP is complete. The local
terminal functions as a control
terminal.
See the
6500 Series Introduction Manual
for additional information about the
CTP.
Steps to Default Port 3 CTP Configuration
Follow these steps to default Port 3 to 9600 kbps, 8N1.
Step
Action
1
From the front panel of the unit, set the switch CTP -> Port 3to the Up
position.
2
Reset or power cycle the unit.
3
For APAD access, enter .ctp, or for ATPAD access, enter ATDS0, and
configure port parameters.
4
Set the CTP -> Port 3 switch to the Down position. Reset or power cycle
the unit.
5
Reset or power cycle the unit.
6
Reboot to verify that the configuration in configuration memory is
operating.
Refer to the
6500 Series Configuration and Administration Manual
for additional
information about configuration.