NEC MA431-MPi4E User Manual English - Page 19

Mounting (for Trained Installers

Get NEC MA431-MPi4E PDF manuals and user guides View all NEC MA431-MPi4E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Mounting (for Trained Installers)  WARNING: Please refer to "WARNING 9". Carefully inspect the location where the unit is to be mounted. Not all walls or ceilings are capable of supporting the weight of the unit. The weight of this monitor is provided in the specifications (see "P435" on page 76, "P495" on page 77, "P555" on page 78, "MA431" on page 79, "MA491" on page 80 and "MA551" on page 81). Product warranty does not cover damage caused by improper installation, re-modeling, or natural disasters. Failure to comply with these recommendations could result in voiding the warranty. To ensure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two points on the installation location.  WARNING: Please refer to the "Important Information" section. Please note the following when mounting on a wall or ceiling: • When using mounting accessories other than those that are NEC approved, they must comply with the VESA-compatible (FDMlv1) mounting method. • NEC recommends mounting interfaces that comply with UL1678 standard in North America. • Prior to mounting, inspect the installation location to ensure that it is strong enough to support the weight of the unit so that the unit will be safe from harm. • For detailed information, refer to the instructions included with the mounting equipment. NEC strongly recommends using the screws as shown below. If using screws longer than below mentioned, check the depth of the hole. Unit No thread D C (A) (B) Screw Size Bracket Hole (C) No Thread (D) Recommended Fasten Force B M6 10-12 mm + thickness of bracket and washer in length ≤ Ø 8.5 mm 4.5 mm 390 ~ 670 N•cm Gap Mounting Bracket Washers A Thickness of bracket and washers  NOTE: When used in a video wall configuration for a long time, slight expansion of the monitors may happen due to temperature changes. It is recommended that a gap of over one millimeter is kept between adjacent monitor edges. > 1 mm > 1 mm English−15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
English−15
Mounting (for Trained Installers)
WARNING°
Please refer to
“WARNING 9”
.
Carefully inspect the location where the unit is to be mounted. Not all walls or ceilings are capable of supporting the weight of
the unit. The weight of this monitor is provided in the specifications (see
“P435” on page 76
,
“P495” on page 77
,
“P555”
on page 78
,
“MA431” on page 79
,
“MA491” on page 80
and
“MA551” on page 81
). Product warranty does not cover
damage caused by improper installation, re-modeling, or natural disasters. Failure to comply with these recommendations could
result in voiding the warranty.
To ensure safe installation, use two or more brackets to mount the unit. Mount the unit to at least two points on the installation
location.
WARNING°
Please refer to the
“Important Information”
section.
Please note the following when mounting on a wall or ceiling:
•
When using mounting accessories other than those that are NEC approved, they must
comply with the VESA-compatible (FDMlv1) mounting method.
•
NEC recommends mounting interfaces that comply with UL1678 standard in North America.
•
Prior to mounting, inspect the installation location to ensure that it is strong enough to
support the weight of the unit so that the unit will be safe from harm.
•
For detailed information, refer to the instructions included with the mounting equipment.
NEC strongly recommends using the screws as shown below.
If using screws longer than below mentioned, check the depth of the hole.
Screw Size
Bracket Hole
(C)
No Thread
(D)
Recommended
Fasten Force
(A)
(B)
M6
10-12 mm
+ thickness of bracket and washer in length
≤
Ø
8.5 mm
4.5 mm
390 ~ 670 N•cm
NOTE°
When used in a video wall configuration for a long time, slight expansion of the monitors may happen due to
temperature changes. It is recommended that a gap of over one millimeter is kept between adjacent monitor edges.
> 1 mm
> 1 mm
A
Unit
C
Washers
Mounting
Bracket
No thread
D
Thickness of
bracket and
washers
B
Gap