NEC NC900C-A User Manual - Page 82

Input Connector, tasks, such as lamp cooling and switching title.

Get NEC NC900C-A PDF manuals and user guides View all NEC NC900C-A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

6. Appendix Input Connector GP I/O Connector Ext_GPIN_P Pin No.: 1 2 3 4 5 6 7 8 Voltage applied across the pins of Ext_GPIN_P and Ext_GPIN_N should be in the range from 3.3 Vdc to 10 Vdc. Recommended Operating Current: 5mA Absolute Maximum Rating: 23mA Ext_GPIN_N Pin No.: 20 21 23 23 24 25 26 27 Inside Projector Resist = 390 Ω Photo-coupler Forward direction voltage: 1.1V (@5mA) • Using GPIO Control Momentary "ON" pulse enables you to control projector. To enable "ON" pulse, hold it for at least 500 ms. Hold "OFF" for at least 500 ms before "ON". (See page 83) Here is function list to control projector by using GPIO port. Pin No. Photo-coupler ON/OFF Function 1-20 ON/OFF 3D L/R timing signal input ON/OFF 2-21 ON/OFF 3D L/R display timing signal input ON/OFF 3-22 - System reserved (used internally) 4-23 - System reserved (used internally) 5-24 6-25 7-26 8-27 8-27 OFF OFF 7-26 OFF OFF 6-25 OFF ON 5-24 ON OFF The following functions apply depending on the combination of input terminals. Power ON Power OFF OFF OFF ON ON Lamp ON OFF ON OFF OFF Lamp OFF OFF ON OFF ON Image douser ON OFF ON ON OFF Image douser OFF OFF ON ON ON System reserved (used internally) ON OFF OFF OFF Selects the title registered to the preset button 1 ON OFF OFF ON Selects the title registered to the preset button 2 ON OFF ON OFF Selects the title registered to the preset button 3 ON OFF ON ON Selects the title registered to the preset button 4 ON ON OFF OFF Selects the title registered to the preset button 5 ON ON OFF ON Selects the title registered to the preset button 6 ON ON ON OFF Selects the title registered to the preset button 7 ON ON ON ON Selects the title registered to the preset button 8 Example for dousing image: Input ON to 5-24 and 7-26 while 6-25 and 8-27 are OFF. Example for selecting the preset button 2: Input ON to 5-24 and 8-27 while 6-25 and 7-26 are OFF. NOTE • The operation command coming from GPI/O port will be canceled when the projector is processing other tasks, such as lamp cooling and switching title. • Set all other pins than those in use to "OFF". • The operation command is executed upon continuous input of the "ON" pulse for approximately 200 ms. 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
82
6. Appendix
Input Connector
GP I/O Connector
Inside Projector
Resist = 390
Ω
Photo-coupler
Forward direction voltage: 1.1V (@5mA)
Ext_GPIN_P
Pin No.:
1
2
3
4
5
6
7
8
Ext_GPIN_N
Pin No.:
20
21
23
23
24
25
26
27
Voltage applied across the pins of Ext_GPIN_P and
Ext_GPIN_N should be in the range from 3.3 Vdc to 10 Vdc.
Recommended Operating Current: 5mA
Absolute Maximum Rating:
23mA
• Using GPIO Control
Momentary “ON” pulse enables you to control projector. To enable “ON” pulse, hold it for at least 500 ms. Hold “OFF” for at
least 500 ms before “ON”. (See page 83)
Here is function list to control projector by using GPIO port.
Pin No.
Photo-coupler ON/OFF
Function
1-20
ON/OFF
3D L/R timing signal input ON/OFF
2-21
ON/OFF
3D L/R display timing signal input ON/OFF
3-22
-
System reserved (used internally)
4-23
-
System reserved (used internally)
5-24
6-25
7-26
8-27
8-27
7-26
6-25
5-24
The following functions apply depending on the combination of input terminals.
OFF
OFF
OFF
ON
Power ON
OFF
OFF
ON
OFF
Power OFF
OFF
OFF
ON
ON
Lamp ON
OFF
ON
OFF
OFF
Lamp OFF
OFF
ON
OFF
ON
Image douser ON
OFF
ON
ON
OFF
Image douser OFF
OFF
ON
ON
ON
System reserved (used internally)
ON
OFF
OFF
OFF
Selects the title registered to the preset button 1
ON
OFF
OFF
ON
Selects the title registered to the preset button 2
ON
OFF
ON
OFF
Selects the title registered to the preset button 3
ON
OFF
ON
ON
Selects the title registered to the preset button 4
ON
ON
OFF
OFF
Selects the title registered to the preset button 5
ON
ON
OFF
ON
Selects the title registered to the preset button 6
ON
ON
ON
OFF
Selects the title registered to the preset button 7
ON
ON
ON
ON
Selects the title registered to the preset button 8
Example for dousing image:
Input ON to 5-24 and 7-26 while 6-25 and 8-27 are OFF.
Example for selecting the preset button 2: Input ON to 5-24 and 8-27 while 6-25 and 7-26 are OFF.
NOTE
• The operation command coming from GPI/O port will be canceled when the projector is processing other
tasks, such as lamp cooling and switching title.
• Set all other pins than those in use to “OFF”.
• The operation command is executed upon continuous input of the “ON” pulse for approximately 200 ms.