Home » Netgear Manuals » Hubs & Switches » Netgear FS752TPS » Manual Viewer

Netgear FS752TPS FS752TS Hardware manual - Page 19

Connecting Devices to the Switch, Installing an SFP GBIC Module, Use Category 5

Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

FS700TS Hardware Installation Guide Connecting Devices to the Switch The following procedure describes how to connect PCs to the switch's RJ-45 ports. The NETGEAR Smart Switch contains Auto Uplink™ technology, which allows you to attach devices using either straight-through or crossover cables. Figure 2-2 Connect each PC to an RJ-45 network port on the Switch front panel (Figure 2-2). Use Category 5 (Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector for these connections. Note: Ethernet specifications limit the cable length between the switch and the attached device to 100 m (328 ft.). Installing an SFP GBIC Module The following procedure describes how to install an SFP Gigabit Ethernet module in the switch's Gigabit module bay. Standard SFP GBIC modules are sold separately from the Smart Switch. If you do not plan to install an SFP GBIC module at this time, skip this procedure. To install an SFP GBIC module: 1. Insert the SFP module into the SFP module bay. Installation v1.0, September 2007 2-32

Section	Page
FS700TS (728TS, 752TS, 752TPS) Series Hardware Installation Guide	1
Contents	5
About This Guide	7
Conventions, Formats and Scope	7
How to Use This Manual	8
How to Print this Manual	8
Revision History	9
Chapter 1 Introduction	10
Overview	10
Switch Features	12
Stacking	14
Package Contents	15
Chapter 2 Installation	16
Preparing the Site	16
Installing the Switch	17
Installing the Switch on a Flat Surface	17
Installing the Switch in a Rack	17
Checking the Installation	18
Connecting Devices to the Switch	19
Installing an SFP GBIC Module	19
Installing Device as Stand-alone or Stack Master	20
Applying AC Power	21
Managing the Switch using a Web Browser or the PC Utility for Initial Configuration	21
Chapter 3 Physical Description	22
Front and Back Panel Configuration	22
FS728TS Front and Back Panels	22
FS752TS Front and Back Panels	23
FS752TPS Front and Back Panels	24
LED Designations	25
Port LEDs	25
System LEDs	27
Device Hardware Interfaces	28
RJ-45 Ports	28
SFP GBIC Module	29
Factory Defaults Button	29
Appendix A Troubleshooting	30
Troubleshooting Chart	30
Additional Troubleshooting Suggestions	31
Network Adapter Cards	31
Configuration	31
Switch Integrity	31
Auto-negotiation	32
Appendix B Technical Specifications	33
Network Protocol and Standards Compatibility	33
Management	33
Interface	33
LEDs	34
Per port (Gigabit): Link/Activity, Speed, Stack (for stacking-enabled ports)	34
Performance Specifications	34
Power Supply	34
Physical Specifications	34
Environmental Specifications	34
Electromagnetic Emissions	34
Electromagnetic Immunity	35
Safety	35
Modules	35

Match case Limit results 1 per page

FS700TS Hardware Installation Guide

Installation

2-32

v1.0, September 2007

Connecting Devices to the Switch

The following procedure describes how to connect PCs to the switch’s RJ-45 ports. The

NETGEAR Smart Switch contains Auto Uplink™ technology, which allows you to attach devices

using either straight-through or crossover cables.

Connect each PC to an RJ-45 network port on the Switch front panel (

Figure 2-2

). Use Category 5

(Cat5) Unshielded Twisted-Pair (UTP) cable terminated with an RJ-45 connector for these

connections.

Installing an SFP GBIC Module

The following procedure describes how to install an SFP Gigabit Ethernet module in the switch’s

Gigabit module bay. Standard SFP GBIC modules are sold separately from the Smart Switch. If

you do not plan to install an SFP GBIC module at this time, skip this procedure.

To install an SFP GBIC module:

Insert the SFP module into the SFP module bay.

Figure 2-2

Note:

Ethernet specifications limit the cable length between the switch and the attached

device to 100 m (328 ft.).