Home » Netgear Manuals » Hubs & Switches » Netgear GS516TP » Manual Viewer

Netgear GS516TP Hardware Installation Guide - Page 14

Reset Button, Factory Defaults Button, Physical Description, GS516TP Gigabit PoE Smart Switch - password

Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

GS516TP Gigabit PoE Smart Switch Reset Button The smart switch has a Reset button on the front panel to allow you to manually reboot the switch. This action is equivalent to powering the unit off and back on. The last saved configuration is loaded into the switch as it resets. To operate the Reset button, insert a device such as a paper clip into the opening to press the recessed button. The front panel LEDs turn off and light again as the switch performs its power-on self-test (POST). Factory Defaults Button The smart switch has a Factory Defaults button on the front panel so that you can remove the current configuration and return the device to its factory settings. When you press the Factory Defaults button, all settings including the password, VLAN settings, and port configurations are removed. To operate the Factory Defaults button, insert a device such as a paper clip into the opening to press the recessed button for over two seconds. Physical Description 14

Section	Page
ProSAFE GS516TP Gigabit PoE/PD Smart Switch	1
Technical Support	2
Statement of Conditions	2
Revision History	2
Contents	3
1. Introduction	5
Overview	6
Features	6
Package Contents	8
2. Physical Description	10
GS516TP Front Panel and Back Panel Configuration	11
LED Designations	12
Port LEDs	12
System LEDs	13
Device Hardware Interfaces	13
RJ-45 Ports	13
Reset Button	14
Factory Defaults Button	14
3. Applications	15
Desktop Switching	16
Backbone Switching	17
4. Installation	18
Prepare the Site	19
Install the Switch	19
Install the Switch on a Flat Surface	19
Install the Switch in a Rack	19
Check the Installation	20
Connect Devices to the Switch	21
Apply AC Power	21
Apply DC Power Through PD Ports 15 or 16	22
Manage the Switch Using a Web Browser or the Smart Control Center Utility	22
A. Troubleshooting	24
Troubleshooting Chart	25
Additional Troubleshooting Suggestions	25
Network Adapter Cards	25
Configuration	25
Switch Integrity	26
Autonegotiation	26
B. Technical Specifications	27
Network Protocol and Standards Compatibility	27
Management	27
Interface	28
LEDs	28
Performance Specifications	28
Power Supply	29
Physical Specifications	29
Environmental Specifications	29
Electromagnetic Emissions	29
Safety	29
C. Notification of Compliance	30
Regulatory Compliance Information	30
Europe – EU Declaration of Conformity	30
FCC Requirements for Operation in the United States	30
FCC Information to User	30
FCC Guidelines for Human Exposure	30
FCC Declaration Of Conformity	30
FCC Radio Frequency Interference Warnings & Instructions	31
TV Tuner (on Selected Models)	31

Match case Limit results 1 per page

Physical Description

GS516TP Gigabit PoE Smart Switch

Reset Button

The smart switch has a Reset button on the front panel to allow you to manually reboot the

switch. This action is equivalent to powering the unit off and back on. The last saved

configuration is loaded into the switch as it resets. To operate the Reset button, insert a

device such as a paper clip into the opening to press the recessed button. The front panel

LEDs turn off and light again as the switch performs its power-on self-test (POST).

Factory Defaults Button

The smart switch has a Factory Defaults button on the front panel so that you can remove the

current configuration and return the device to its factory settings. When you press the Factory

Defaults button, all settings including the password, VLAN settings, and port configurations

are removed. To operate the Factory Defaults button, insert a device such as a paper clip

into the opening to press the recessed button for over two seconds.