Home » Netgear Manuals » Hubs & Switches » Netgear GS748TPS » Manual Viewer

Netgear GS748TPS GS7xxTPS User Manual - Page 15

Switch Management Interface - vlan

UPC - 606449061116

Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

GS700TPS Smart Switch Software Administration Manual Note: For complete hardware installation instructions, refer to the GS700TPS Smart Switch Hardware Installation Manual included on your Resource CD, or go to http://www.netgear.com/support. Switch Management Interface Your NETGEAR GS700TPS Gigabit Stackable PoE Smart Switch contains an embedded web server and management software for managing and monitoring switch functions. This switch operates as a simple switch without using the management software. The management software enables you to configure more advanced features, and consequently improve switch efficiency as well as overall network performance. Web-Based Management enables you to monitor, configure, and control your switch remotely using a common web browser, instead of having to use expensive and complicated SNMP software products. Simply by using your web browser, you can monitor the performance of your switch and optimize network configuration. Using your browser, for example, you can set up VLANs, traffic priority, and configure port trunking. In addition, NETGEAR provides the SmartWizard Discovery utility with this product. This program runs under Microsoft Windows XP or Windows 2000 and provides a "front end" that discovers the switches on your network segment. When you power up your switch for the first time, the SmartWizard Discovery utility enables you to configure its basic network parameters without prior knowledge of IP address or subnet mask. Following such configuration, this program leads you into the Web Management interface. Some features of the SmartWizard Discovery utility and Web Management interface are shown in the table below. Getting Started with Switch Management 1-2 v1.0, June 2009

Section	Page
GS700TPS Smart Switch Software Administration Manual	1
Contents	5
About This Manual	10
Who Should Use this Book	10
How to Use This Book	10
Conventions, Formats, and Scope	11
How to Use This Manual	12
How to Print this Manual	13
Revision History	13
Chapter 1 Getting Started with Switch Management	14
System Requirements	14
Switch Management Interface	15
Network with a DHCP Server	16
Network without a DHCP Server	18
Manually Assigning Network Parameters	18
NIC Setting on the Host that Accesses the GS700TPS Gigabit Stackable PoE Smart Switch	20
Web Access	21
Additional Utilities	22
Password Change	22
Firmware Upgrade	22
Exit	23
Chapter 2 Introduction to the Web Browser Interface	24
Logging Into the NETGEAR Home Screen	24
The Navigation Menu	25
Using the NETGEAR Web Management System Options	26
Device Management Buttons	26
Informational Services	27
Help Navigation Tab	27
Accessing Device Information	27
Using Screen and Table Options	28
Selecting an Entry	29
Adding an Entry	29
Modifying an Entry	30
Deleting an Entry	31
Special Table Options	31
Gold Buttons	31
Quick Boxes	32
Interface View and Selection	33
Chapter 3 Managing System Settings	35
Using the System Settings Utility	35
Management	35
System Information	35
IP Configuration	38
Time	39
Time Configuration	39
SNTP Server Configuration	40
Device View	42
Stacking	42
Operation Modes	43
Understanding Stack Topology	44
Stacking Ports	44
Stacking Members and Unit No.	44
Removing and Replacing Stacking Members	45
Inserting a Stacking Member	46
Exchanging Stacking Members	46
Switching the Stacking Master	47
Stack Configuration and Management	47
Basic	47
Stack Configuration	47
Advanced	49
Stack Configuration	49
Stack Management	50
PoE	51
Basic	52
PoE Configuration	52
Advanced	53
PoE Configuration	53
PoE Port Configuration	55
SNMP	57
SNMPv1/v2	58
Community Configuration	58
Trap Configuration	60
SNMPv3	62
Engine ID	63
View Name	64
View Content	65
Community Configuration	66
Group Configuration	68
User Configuration	70
Global Trap Configuration	72
Trap Configuration	73
Trap Filter Name	75
Trap Filter Content	77
LLDP	78
Basic	79
LLDP Configuration	79
Advanced	81
LLDP Configuration	81
LLDP Port Settings	83
LLDP-MED Network Policy	85
LLDP-MED Port Settings	88
Local Information	89
Neighbors Information	92
LLDP Statistics	97
Chapter 4 Configuring Switching Settings	100
Configuring Switching Settings	100
Ports	100
Port Configuration	101
LAG	103
Basic	104
LAG Configuration	104
LAG Membership	106
Advanced	107
LAG Configuration	108
LAG Membership	110
LACP Configuration	111
LACP Port Configuration	112
VLAN	113
Basic	113
VLAN Configuration	114
Advanced	115
VLAN Configuration	115
VLAN Membership	117
Port PVID Configuration	119
Voice VLAN	121
Basic	121
Properties	121
Advanced	123
Properties	123
Port Setting	124
OUI	126
STP	127
Basic	128
STP Configuration	128
Advanced	130
STP Configuration	130
CST Configuration	133
CST Port Configuration	135
RSTP	136
MST Configuration	139
MST Port Configuration	140
Multicast	142
Basic	143
IGMP Snooping Configuration	143
Advanced	144
IGMP Snooping Configuration	145
Multicast Group Configuration	147
Multicast Group Membership	148
Multicast Forward All	150
Address Table	151
Basic	151
Address Table	152
Advanced	153
Static Addresses	153
Dynamic Addresses	154
Address Table	155
Chapter 5 Configuring QoS	157
Configuring the Basic and Advanced QoS Settings	157
CoS	157
Basic	158
CoS Global Configuration	158
CoS Interface Configuration	159
Queue	161
Bandwidth	161
Advanced	163
CoS to Queue Mapping	163
DSCP to Queue Mapping	165
Creating Class Mapping	166
Policy Table Mapping	167
Policy Binding	169
Chapter 6 Managing Security	170
Setting Security Configuration Options	170
Management Security	170
User Configuration	170
Change Password	171
RADIUS	171
Accounting Server Configuration	173
TACACS+	174
Authentication List	176
Port Authentication	177
Basic	178
802.1X Configuration	178
Advanced	179
802.1X Configuration	179
Port Authentication	181
Traffic Control	184
Storm Control	184
Port Security	186
Protected Ports	188
ACL	190
MAC ACL	190
MAC Rules	192
MAC Binding Configuration	193
IPv4 ACL	194
IPv4 Rules	195
IPv4 Binding Configuration	197
IPv6 ACL	198
IPv6 Rules	200
IPv6 Binding Configuration	202
Binding Table	203
Chapter 7 Monitoring the Switch	204
Setting Monitoring Options	204
Logs	204
Logs Configuration	205
Log Filter	206
Memory Log	207
Flash Log	209
Server Log	210
RMON	212
Basic	212
Statistics	213
Advanced	214
Statistics	214
History Control	217
History Table	219
Events Control	221
Events Log	222
Alarms	223
Port Mirroring	225
Port Mirroring	226
Chapter 8 Maintenance	228
Using the Maintenance Options	228
Reset	228
Device Reboot	228
Factory Default	229
Upload	230
Upload	230
Download	232
Download	232
File Management	233
Active Image	233
Troubleshooting	234
Diagnostics	234
Cable Test	234
Chapter 9 Online Help	237
Online Help	237
Support	237
User Guide	238
Appendix A Default Settings	239

Match case Limit results 1 per page

GS700TPS Smart Switch Software Administration Manual

Getting Started with Switch Management

1-2

v1.0, June 2009

Switch Management Interface

Your NETGEAR GS700TPS Gigabit Stackable PoE Smart Switch contains an embedded web

server and management software for managing and monitoring switch functions. This switch

operates as a simple switch without using the management software. The management software

enables you to configure more advanced features, and consequently improve switch efficiency as

well as overall network performance.

Web-Based Management enables you to monitor, configure, and control your switch remotely

using a common web browser, instead of having to use expensive and complicated SNMP

software products. Simply by using your web browser, you can monitor the performance of your

switch and optimize network configuration. Using your browser, for example, you can set up

VLANs, traffic priority, and configure port trunking.

In addition, NETGEAR provides the SmartWizard Discovery utility with this product. This

program runs under Microsoft Windows XP or Windows 2000 and provides a “front end” that

discovers the switches on your network segment. When you power up your switch for the first

time, the SmartWizard Discovery utility enables you to configure its basic network parameters

without prior knowledge of IP address or subnet mask. Following such configuration, this program

leads you into the Web Management interface.

Some features of the SmartWizard Discovery utility and Web Management interface are shown in

the table below.

Note:

For complete hardware installation instructions, refer to the

GS700TPS Smart

Switch Hardware Installation Manual

included on your

Resource CD

, or go to

http://www.netgear.com/support