Netgear GS748Tv3 GS748Tv3 User Manual - Page 17

Manually Assigning Network Parameters, Discover, Configuration Setting, Disable - password

Get Netgear GS748Tv3 - Gigabit Smart Switch PDF manuals and user guides View all Netgear GS748Tv3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Smart Switch Software User Manual GS748T Manually Assigning Network Parameters If your network has no DHCP service, you must assign a static IP address to your switch. If you choose, you can assign a static IP address to the switch even if your network has DHCP service. To manually assign a static IP address to your switch: 1. Connect the GS748T Smart Switch to your existing network. 2. Power on the switch by plugging in the power cord (Default IP is 192.168.0.239). 3. Install the Smartwizard Discovery Utility program on your computer 4. Start the Smartwizard Discovery utility. 5. Click Discover for the Smartwizard Discovery Utility to find your GS748T Smart Switch. You should see a screen similar to that shown in Figure 2-1 on page 2-1. 6. Click on Configuration Setting. A screen similar to that shown below appears. Figure 2-3 7. Choose the Disable radio button for DHCP. 8. Enter your chosen switch IP address, gateway IP address and subnet mask, and then type your password and click Set. Please ensure that your PC and the GS748T Smart Switch are in the same subnet. Make a note of these settings for later use. Using the Smartwizard Discovery Utility 2-3 v1.0, October 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Smart Switch Software User Manual GS748T
Using the Smartwizard Discovery Utility
2-3
v1.0, October 2007
Manually Assigning Network Parameters
If your network has no DHCP service, you must assign a static IP address to your switch. If you
choose, you can assign a static IP address to the switch even if your network has DHCP service.
To manually assign a static IP address to your switch:
1.
Connect the GS748T Smart Switch to your existing network.
2.
Power on the switch by plugging in the power cord (Default IP is 192.168.0.239).
3.
Install the Smartwizard Discovery Utility program on your computer
4.
Start the Smartwizard Discovery utility.
5.
Click
Discover
for the Smartwizard Discovery Utility to find your GS748T Smart Switch. You
should see a screen similar to that shown in
Figure 2-1 on page 2-1
.
6.
Click on
Configuration Setting
. A screen similar to that shown below appears.
7.
Choose the
Disable
radio button for DHCP.
8.
Enter your chosen switch IP address, gateway IP address and subnet mask, and then type your
password and click
Set
. Please ensure that your PC and the GS748T Smart Switch are in the
same subnet. Make a note of these settings for later use.
Figure 2-3