Netgear GSM7248R CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw
Netgear GSM7248R Manual
View all Netgear GSM7248R manuals
Add to My Manuals
Save this manual to your list of manuals |
Netgear GSM7248R manual content summary:
- Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 1
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches with Static Routing, Software Version 7.3 NETGEAR, Inc. 350 Plumeria Dr. San Jose, CA 95124 USA 202-10455-01 October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 2
document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. EN 55 022 Declaration of Conformance This is to certify that the ProSafe the notes in the operating instructions. The Federal Office for - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 3
Number: Publication Date: Product Family: Product Name: Home or Business Product: Language: Publication Part Number: Publication Version Number FSM7226RS October 2008 managed switch ProSafe 7200RS Series Layer-2 Managed Stackable Switch Business English 202-10455-01 1.0 iii v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 4
iv v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 5
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches with Static Routing, Software Version 7.3 Chapter 1 About This Manual 1.1 Audience...1-1 1.2 Scope...1-1 1.3 Typographical Conventions 1-2 1.4 Special Message Formats 1-2 1.5 How to Use This Manual 1-3 1.6 How to Print - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 6
Protocol (HTTP) Commands 3-16 3.6.1 ip http secure-port 3-16 3.6.2 ip http secure-protocol 3-17 3.6.3 ip http secure-server 3-17 3.6.4 ip http server 3-17 3.6.5 ip http java 3-18 3.6.6 ip http session hard-timeout 3-18 3.6.7 ip http session maxsessions 3-18 3.6.8 ip http session soft-timeout - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 7
3.7.6 show loginsession 3-25 3.7.7 show users 3-25 3.7.8 disconnect 3-26 Chapter 4 Port and System Setup Commands 4.1 Port Configuration Commands 4-1 4.1.1 interface...4-1 4.1.2 interface range 4-2 4.1.3 interface vlan 4-2 4.1.4 interface lag 4-2 4.1.5 auto-negotiate 4-2 4.1.6 auto-negotiate - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 8
4.1.19 show port status 4-9 4.2 Pre-login Banner and System Prompt Commands 4-10 4.2.1 copy...4-10 4.2.2 set prompt static 4-23 4.4.12 show mac-address-table stats 4-23 4.5 DNS Client Commands 4-24 4.5.1 ip domain-lookup 4-25 4.5.2 ip domain-name 4-25 4.5.3 ip name-server 4-25 4.5.4 ip host - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 9
max-hops 5-6 5.1.12 spanning-tree mst 5-6 5.1.13 spanning-tree mst instance 5-7 5.1.14 spanning-tree mst priority 5-8 5.1.15 spanning-tree mst vlan 5-9 5.1.16 spanning-tree port mode 5-9 5.1.17 spanning-tree port mode all 5-9 5.1.18 spanning-tree bpduforwarding 5-10 5.2 STP Show Commands - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 10
6.1.19 protocol vlan group 6-9 6.1.20 protocol vlan group all 6-9 6.1.21 vlan pvid ...6-10 6.1.22 vlan tagging 6-10 6.2 VLAN Show Commands 6-11 6.2.1 show vlan ...6-11 6.2.2 show vlan - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 11
vlan priority 6-18 Chapter 7 DHCP Commands 7.1 ip dhcp pool ...7-2 7.1.1 client-identifier 7-2 7.1.2 client-name...7-3 7.1.3 default-router 7-8 7.2.1 ip dhcp excluded-address 7-8 7.2.2 ip dhcp ping packets 7-9 7.2.3 service dhcp 7-9 7.2.4 ip dhcp bootp automatic 7-10 7.2.5 ip dhcp conflict - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 12
7.4.1 ip dhcp relay information option 7-15 7.4.2 bootpdhcprelay 7-15 7.4.3 bootpdhcprelay maxhopcount 7-16 7.4.4 bootpdhcprelay port-security 9-1 9.1.2 port-security max-dynamic 9-2 9.1.3 port-security max-static 9-3 9.1.4 port-security mac-address 9-3 9.1.5 port-security mac-address move - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 13
9.2 Storm Control Commands 9-5 9.2.1 storm-control broadcast 9-5 9.2.2 storm-control multicast all 9-6 9.2.3 storm-control unicast all 9-6 9.2.4 storm-control broadcast 9-7 9.2.5 storm-control multicast 9-7 9.2.6 storm-control unicast 9-8 9.2.7 storm-control flowcontrol 9-8 9.2.8 show storm- - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 14
.1.12 dot1x system-auth-control 11-6 11.1.13 dot1x timeout 11-6 11.1.14 dot1x port-method 11-8 11.1.15 dot1x user 11-8 11.1.16 users defaultlogin 11-8 11.1.17 users login 11-9 11.1.18 show authentication 11-9 11.1.19 show authentication users 11-9 11.1.20 show dot1x 11-10 11.1.21 show dot1x - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 15
-24 11.4.8 port ...11-24 11.4.9 priority...11-24 11.4.10 timeout 11-24 11.4.11 show tacacs 11-24 Chapter 12 Port-Channel/LAG (802.3ad) Commands 12.1 Port-Channel Configuration Commands 12-1 12.1.1 addport ...12-2 12.1.2 deleteport (Interface Config 12-2 12.1.3 deleteport (Global Config 12-2 12 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 16
12.2.2 show port-channel 12-6 Chapter 13 Quality of Service (QoS) Commands 13.1 Class of Service (CoS) Commands 13-1 13.1.1 classofservice dot1p-mapping 13-2 13.1.2 classofservice ip-precedence-mapping 13-2 13.1.3 classofservice ip-dscp-mapping 13-3 13.1.4 classofservice trust 13-3 13.1.5 cos - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 17
-18 13.4.5 class ...13-18 13.4.6 mark cos 13-19 13.4.7 mark ip-dscp 13-20 13.4.8 mark ip-precedence 13-20 13.4.9 police-simple 13-20 13.4.10 policy-map rename 13-21 13.5 DiffServ Service Commands 13-21 13.5.1 service-policy 13-21 13.6 DiffServ Show Commands 13-22 13.6.1 show class - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 18
-5 14.1.11 show arp brief 14-6 14.2 IP Routing Commands 14-7 14.2.1 routing ...14-7 14.2.2 ip routing...14-7 14.2.3 ip address 14-8 14.2.4 ip route ...14-8 14.2.5 ip route default 14-9 14.2.6 ip route distance 14-9 14.2.7 ip forwarding 14-10 14.2.8 ip mtu...14-10 14.2.9 encapsulation 14-11 14 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 19
14.2.15 show ip route bestroutes 14-15 14.2.16 show ip route entry 14-15 14.2.17 show ip route preferences 14-16 14.2.18 show ip stats 14-17 14.3 Virtual LAN Routing Commands 14-17 14.3.1 vlan routing 14-17 14.3.2 show ip vlan 14-17 14.4 Virtual Router Redundancy Protocol (VRRP) Commands 14- - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 20
14.5.21 default-information originate (OSPF 14-33 14.5.22 default-metric (OSPF ip ospf interface 14-45 14.5.44 show ip ospf interface - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 21
14-52 14.5.51 show ip ospf virtual-link - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 22
ip igmpsnooping querier 15-10 15.3.2 ip igmpsnooping querier ip-address 15-10 15.3.3 ip igmpsnooping querier query-interval 15-11 15.3.4 show ip 12 show slot 16-6 16.1.13 show supported cardtype 16-7 16.1.14 show switch 16-8 16.1.15 show supported switchtype 16-9 16.2 Front Panel Stacking - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 23
17.1.3 lldp receive 17-1 17.1.4 no lldp receive 17-2 17.1.5 lldp timers 17-2 17.1.6 no lldp timers 17-2 17.1.7 lldp transmit-tlv 17-2 17.1.8 no lldp transmit-tlv 17-3 17.1.9 lldp transmit-mgmt 17-3 17.1.10 no lldp transmit-mgmt 17-3 17.1.11 lldp notification 17-3 17.1.12 no lldp - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 24
18-18 18.2.5 clear pass 18-19 18.2.6 enable passwd 18-19 18.2.7 clear port-channel 18-19 18.2.8 clear traplog 18-19 18.2.9 clear vlan 18-19 18.2.10 copy...18-19 18.2.11 logout...18-21 18.2.12 ping...18-21 18.2.13 reload ...18-22 18.3 Logging Commands - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 25
length 18-32 18.8.2 terminal no length 18-32 18.9 Save...18-32 Chapter 19 UDP Relay Commands 19.1 UDP Relay Configuration Commands 19-2 19.1.1 ip helper-address (global config mode 19-2 19.1.2 ip helper-address (interface config mode 19-3 19.2 UDP Relay Show Commands 19-3 19.2.1 show - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 26
xxvi v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 27
This Manual This chapter introduces the Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches with Static Routing, or SSH over a remote network connection. 1.1 Audience This document is for system administrators who configure and operate systems using 7200RS - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 28
site at http://kbserver.netgear.com/products/. 1.3 Typographical Conventions This guide uses the following typographical conventions: Table 1-2. Typographical conventions Italic Bold Fixed Italic Emphasis, books, CDs, file and server names, extensions User input, IP addresses, GUI screen text - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 29
ProSafe 7200RS Series Layer-2 Stackable Switches Danger: Ignoring this type of warning could result in personal injury or death. 1.5 How to Use This Manual The HTML version of this manual is described in the manual. •A button to access the full NETGEAR, Inc. online knowledge base for the product - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 30
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches - Click the print icon in the window toolbar. Tip: If your printer supports printing of two lists the revision history of this manual. Table 1-3. Revision History of This Manual Document Part Number 202-10455-01 Version - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 31
to Feature Support Among the 7200RS Series Switches Commands Documented in Chapter FSM726E FSM7226RS Switch Model FSM7250RS GSM7224R GSM7248R Routing 14 base runs varies depending upon the platform and requirements of NETGEAR. 7200RS Series Stackable Switch software includes a set of - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 32
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches • Simple Network Parameters can be required or optional values. Some commands, such as show network or clear vlan, do not require parameters. Other commands, such as network parms, require that you supply a - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 33
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Default shows the default value, if any, of a configurable setting on the device. The show commands also contain a description of the information that the command displays. 2.2.2 Command Conventions In this document - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 34
the ProSafe 7200RS (" ") are not valid user-defined strings. Table 2-3 describes have the same format as IP addresses but are distinct from IP addresses. You can use the IP network number of the sub- is applicable in the case of a port-channel (LAG). You can use the logical unit/slot/port to configure - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 35
ProSafe LAG) interfaces are logical interfaces that are only used for bridging functions. VLAN routing interfaces are only used for routing the action of a command or reset a value back to the default. For example, the no a disabled feature or to enable a feature that is disabled by default. Only - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 36
and the prompts visible in that mode. Table 2-6. CLI Command Modes Command Mode User EXEC Prompt Switch> Privileged EXEC Switch# Global Config Switch (Config)# VLAN Config Interface Config Switch (Vlan)# Switch (Interface )# Line Config Switch (line)# Policy Map Config - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 37
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Table 2-6. CLI Command Exit or Access Previous Mode User EXEC Privileged EXEC Global Config VLAN Config Interface Config Line Config This is the first level of access. From the User EXEC mode, enter enable. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 38
Reference for the ProSafe 7200RS Series Layer mac access-list extended . From the Global Config mode, enter ip dhcp pool . Stack Global Config Mode From the Global Config CLI Commands The 7200RS Series Stackable Switch supports several features to help you enter commands. 2.2.6.1 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 39
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 2.2.6.2 CLI of command entry. You can access this list from the CLI by entering help from the User or Privileged EXEC modes. Table 2-9. CLI Editing Conventions Key Sequence Description DEL or Backspace Ctrl - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 40
ProSafe >? enable help logout ping show Enter into user privilege mode. Display help for various special keys the network config protocol. Configure the Management VLAN ID of the switch. If the help #network parms ? Enter the IP Address. If there are no additional command keywords - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 41
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches You can also cannot access the system remotely until the system has an IP address and subnet mask. You can set the network configuration information manually, or you can configure the system to accept these - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 42
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 2-12 v1.0, October 2008 Overview - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 43
3.6 "Hypertext Transfer Protocol (HTTP) Commands" on page 16 • Section 3.7 "User Account Commands" on page 22 The commands in this section are divided into two , statistics, and other information. • Configuration commands configure features and options of the switch. For every configuration command, - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 44
IP Address and the gateway must be on the same subnet. Format network (parms | parameter) [] Mode Privileged EXEC 3.1.3 network mgmt_vlan This command configures the Management VLAN ID. Default for the switch manually. Default none Format network protocol - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 45
for the ProSafe 7200RS Series routed. Format show network Modes Privileged EXEC User EXEC IP Address The IP address of the interface. The factory default value is 0.0.0.0 Subnet Mask The IP subnet mask for this interface. The factory default value is 0.0.0.0 Default Gateway The default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 46
applet in the header frame. Enabled means the applet can be viewed. The factory default is disabled. Specifies if NETGEAR 7000-series managed switches, and allows you to configure the following parameters: 1. The administrator's user password and administrator-enable password 2. Management CPU IP - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 47
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches The following is an example of an ezconfig session. NETGEAR EZ Configuration Utility Hello and Welcome! This utility will walk you thru assigning the IP address for the switch management CPU. It will allow you - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 48
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches There are changes detected, From the Global Config mode, you can configure a variety of system settings, including user accounts. From the Global Config mode, you can enter other command modes, including Line - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 49
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 3.3.3 serial baudrate This command specifies the communication rate of the terminal interface. The supported rates are 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200. Default 9600 Format serial baudrate - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 50
serial Modes Privileged EXEC User EXEC Serial Port Login Timeout (minutes) Specifies the time, in minutes, of inactivity on a Serial port connection, after which the Switch will close the connection. Any numeric value between 0 and 160 is allowed, the factory default is 5. A value of 0 disables - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 51
for the ProSafe 7200RS Series be a valid IP address. Valid values for port should be a valid decimal integer in the range of 0 to 65535, where the default value is 23. port> [debug] [line] [noecho] Modes Privileged EXEC User EXEC 3.4.2 transport input telnet This command regulates new telnet - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 52
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 3.4.3 transport output telnet active until the session is ended or an abnormal network error ends it. Default enabled Format transport output telnet Mode Line Config 3.4.3.1 no transport output telnet - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 53
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 3.4.5 session-timeout This command sets the telnet session timeout value.The timeout value unit of time is minutes. A value of 0 indicates that a session remains active indefinitely. Default 0 Format session-timeout - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 54
Interface Reference for the ProSafe 7200RS Series Layer-2 sets the telnet connection session timeout value to the default. Note: Changing the timeout value for active sessions does Format show telnet Modes Privileged EXEC User EXEC Outbound Telnet Login Timeout Indicates the number of minutes - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 55
Reference for the ProSafe 7200RS Series Layer-2 User EXEC Remote Connection Login Timeout (minutes) This object indicates the number of minutes a remote connection session is allowed to remain inactive before being logged off. May be specified as a number from 1 to 160. The factory default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 56
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches ip ssh This command is used to enable SSH. Default disabled Format ip ssh Mode Privileged EXEC 3.5.1.1 no ip ssh This command is used to disable SSH. Format no ip ssh Mode Privileged EXEC 3.5.2 ip - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 57
ProSafe 7200RS Series Layer-2 Stackable Switches 3.5.3 sshcon maxsessions This command specifies the maximum number of SSH connection sessions that can be established. A value of 0 indicates that no ssh connection can be established. The range is 0 to 5. Default , to the default. Changing the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 58
port where port can be 1-65535 and the default is port 443. Default 443 Format ip http secure-port Mode Privileged EXEC 3.6.1.1 no ip http secure-port This command is used to reset the SSL port to the default value. Format no ip http secure-port Mode Privileged EXEC 3-16 v1 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 59
the Web interface. When access is disabled, you cannot login to the switch's Web server. Disabling the Web interface takes effect immediately and affects all interfaces. Default enabled Format ip http server Mode Privileged EXEC 3.6.4.1 no ip http server This command disables access to the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 60
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 3.6.5 ip http java This command enables the Web Java mode. The Java mode applies to both secure and unsecure Web connections. Default enabled Format ip http java Mode Privileged EXEC 3.6.5.1 no ip http java This - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 61
timeout expires the user will be forced to re-authenticate. This timer begins on initiation of the Web session and is restarted with each access to the switch. Default 60 Format ip http session soft-timeout Mode Privileged EXEC 3.6.8.1 no ip http session soft-timeout Resets the soft - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 62
soft-timeout Resets the soft timeout for secure HTTP sessions to the default value. Format no ip http secure-session soft-timeout Mode Privileged EXEC 3.6.12 network javamode This command specifies whether or not the switch should allow access to the Java applet in the header frame of the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 63
This command disallows access to the Java applet in the header frame of the Web interface. When access is disabled, the user cannot view the Java applet. Format no network javamode Mode Privileged EXEC 3.6.13 show ip http This command displays the http settings for the switch. Format - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 64
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 3.7 User Account Commands This section describes the commands you use to add, manage, and delete system users. The 7200RS Series Stackable Switch has two default users: admin and guest. The admin user can view and configure - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 65
not case-sensitive. When you change a password, a prompt asks for the old password. If there is no password, press enter. Default no password Format users passwd Mode Global Config 3.7.2.1 no users passwd This command sets the password of an existing user to blank. When you change - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 66
md5 or sha, the login password is also used as the snmpv3 authentication password and therefore must be at least eight characters in length. The is the user name associated with the authentication protocol. Default no authentication Format users snmpv3 authentication {none - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 67
show users Mode Privileged EXEC User Name The name the user enters to login using the serial port, Telnet or Web. Access Mode Shows whether the user is able to change parameters on the switch (Read/Write) or is only able to view them (Read Only). As a factory default, the "admin" user has - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 68
mode. This field displays the authentication protocol to be used for the specified login user. This field displays the encryption protocol to be used for the specified login user. 3.7.8 disconnect This command closes a telnet session. Format disconnect { | all} Mode Privileged EXEC - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 69
Section 4.1 "Port Configuration Commands" on page 1 • Section 4.2 "Pre-login Banner and System Prompt Commands" on page 10 • Section 4.3 "Simple Network , statistics, and other information. • Configuration commands configure features and options of the switch. For every configuration command, - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 70
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.1.2 interface VLAN group and an IP address assigned to the VLAN group. Format Mode interface lag Global Config 4.1.5 auto-negotiate This command enables automatic negotiation on a port. Default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 71
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.1.5.1 no auto-negotiate This command auto-negotiate all This command enables automatic negotiation on all ports. The default value is enable. Format auto-negotiate all Mode Global Config 4.1.6.1 no auto - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 72
the IP MTU size, which is the maximum size of the IP packet (IP Header + IP payload), see Section 14.2.8 "ip mtu" on page 10. Default Format Mode command on physical and port-channel (LAG) interfaces, but not on VLAN routing interfaces. Default Format Mode enabled shutdown Interface Config - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 73
ProSafe 7200RS Series Layer-2 Stackable Switches 4.1.9.1 no shutdown This command enables a port. Note: You can use the no shutdown command on physical and port-channel (LAG) interfaces, but not on VLAN routing port-channel (LAG) interfaces, but not on VLAN routing interfaces. Default Format Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 74
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Acceptable values are: 100h 100f 10h 10f 100BASE-T half duplex 100BASE-T full duplex 10BASE-T half duplex 10BASE-T full duplex 4.1.12 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 75
ProSafe 7200RS Series Layer-2 Stackable Switches 4.1.13.1 no monitor session This command removes the monitor session (port monitoring) designation from the source probe port, the destination monitored port and all VLANs. Once the port is removed from the VLAN, the user must manually default feature - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 76
for the ProSafe 7200RS Series screens to find out more information. Lag - this port is a member of a port-channel (LAG). Probe - this port is a probe disabled. The factory default is enabled. Physical Mode Selects the desired port speed and duplex mode. If auto-negotiation support is selected, - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 77
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.1.18 show port protocol This command displays the Protocol-Based VLAN information for either the entire system, or for the indicated group. Format show port protocol { | all} Mode Privileged - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 78
for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.2 Pre-login Banner and System Prompt Commands This section describes the commands you use configure the pre-login banner and the system prompt. The pre-login banner is the text that displays before you login at the User: prompt. 4.2.1 copy - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 79
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.3 Simple Network Time no sntp broadcast client poll-interval This command resets the poll interval for SNTP broadcast client back to the default value. Format no sntp broadcast client poll-interval - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 80
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.3.3 sntp client port This command sets the SNTP client port id to a value from 1-65535. Default 123 Format sntp client port Mode Global Config 4.3.3.1 no sntp client port This command resets the SNTP client - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 81
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.3.5.1 no sntp unicast client poll-timeout This command resets the poll timeout for SNTP unicast clients to its default value. Format no sntp unicast client poll-timeout Mode Global Config 4.3.6 sntp - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 82
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.3.8 sntp server This command configures an SNTP server (a maximum of three). The optional priority can be a value of 1-3, the version a - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 83
ProSafe 7200RS Series Layer-2 Stackable Switches Client Supported Modes SNTP Version Port Client Mode Poll Interval Poll Timeout Poll Retry Supported SNTP Modes (Broadcast, Unicast, or Multicast). The highest SNTP version the client supports Privileged EXEC Server IP Address IP Address of - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 84
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Port Last Attempt Time Last Attempt Status UTC Minutes-offset Number of minutes difference with UTC Mode Global Config Default [no] clock timezone 4-16 v1.0, October 2008 Port and System Setup Commands - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 85
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.4 MAC Address address. Default burnedin Format network mac-type {local | burnedin} Mode Privileged EXEC 4.4.2.1 no network mac-type This command resets the value of MAC address to its default. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 86
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.4.3 macfilter This command adds a static MAC filter entry for the MAC address on the VLAN . The parameter must be specified as a 6-byte hexadecimal number in the format of b1:b2: - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 87
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.4.4.1 no macfilter adddest This command removes a port from the destination filter set for the MAC filter with the given and VLAN of . The parameter must be specified as a 6-byte - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 88
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.4.6.1 no macfilter addsrc This command removes a port from the source filter set for the MAC filter with the MAC address of and VLAN of . The parameter must be specified as a 6- - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 89
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 4.4.8 bridge aging-time This command configures the forwarding database address aging timeout in seconds. In an IVL system, the [fdbid | all] parameter is required. Default 300 Format bridge aging-time < - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 90
:AB. In an IVL system the MAC address will be displayed as a MAC address and VLAN ID combination of 8 bytes. Type This displays the type of the entry. Static entries are those that are configured by the end user. Dynamic entries are added to the table as a result of a learning process or protocol - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 91
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Interfaces Forwarding Privileged EXEC MAC Address Is the MAC Address of the static MAC filter entry. VLAN ID Is the VLAN ID of the static MAC filter entry. Source Port(s) Indicates the source port - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 92
when performing a lookup on an unqualified hostname. Static hostname-to-address mappings can be added and removed from the local cache. The DNS client supports 128 entries in the DNS cache. Any application component requiring a DNS lookup may request services from the DNS client. When the DNS client - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 93
ProSafe 7200RS Series Layer-2 Stackable Switches 4.5.1 ip domain-lookup To enable the IP Domain Naming System (DNS)-based host name-to-address translation, use the ip Format [no] ip domain-lookup Mode Global Config Default enabled 4.5.2 ip domain-name To define a default domain name ( - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 94
ProSafe 7200RS Series Layer-2 Stackable Switches 4.5.4 ip host To define static host name to IP address mapping in the host cache, use the ip Mode 4.5.6 show hosts To display the default domain name, a list of name server hosts, the static and the cached list of host names and - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 95
switch settings, statistics, and other information. • Configuration commands configure features and options of the switch. For every configuration command, there to configure Spanning Tree Protocol (STP). Note: STP is enabled by default. If STP is disabled, the system does not generate BPDU messages - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 96
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 5.1.1.1 no spanning-tree This 5.1.3.1 no spanning-tree configuration name This command resets the Configuration Identifier Name to its default. Format no spanning-tree configuration name Mode Global - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 97
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 5.1.4 spanning-tree use in identifying the configuration that this switch is currently using to the default value, i.e. 0. Format no spanning-tree configuration revision Mode Global Config 5.1.5 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 98
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 5.1.6.1 rather than MST BPDUs (IEEE 802.1w functionality supported) • 802.1s - MST BPDUs are transmitted (IEEE 802.1s functionality supported) Default 802.1s Format spanning-tree forceversion - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 99
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 5.1.8.1 no spanning-tree forward-time This command sets the Bridge Forward Delay parameter for the common and internal spanning tree to the default value of 15. Format no spanning-tree forward-time Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 100
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 5.1.11 spanning-tree max-hops This command sets the MSTP Max Hops parameter to a new value for the common and internal spanning tree. The max-hops value is a range from 1 to 127. Default 20 Format spanning-tree - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 101
Reference for the ProSafe 7200RS Series Layer external path cost for this port for mst '0' instance, to the default value, i.e. a path cost value based on the Link Speed. If ID to be added. The maximum number of multiple instances supported by the switch is 4. Format spanning-tree mst instance < - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 102
ProSafe 7200RS Series Layer-2 Stackable Switches 5.1.13.1 no spanning-tree mst instance This command removes a multiple spanning tree instance from the switch and reallocates all VLANs increments of 4096. If you specify 0 (defined as the default CIST ID) as the , this command sets the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 103
ProSafe 7200RS Series Layer-2 Stackable Switches 5.1.15 spanning-tree mst vlan This command adds an association between a multiple spanning tree instance and a VLAN so that the VLAN Switch Port State for all ports to enabled. Default disabled Format spanning-tree port mode all Mode Global - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 104
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 5.1.17.1 no some network setup, the user wishes to forward BDPU packets received from other network devices, this command can be used to enable the forwarding. Default disabled Format spanning-tree - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 105
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Bridge Priority Bridge Identifier Time Since Topology Change Topology Change Count Topology Change Designated Root Root Path Cost Root Port - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 106
ProSafe 7200RS Series Layer-2 Stackable Switches Associated FIDs Associated VLANs List of forwarding database identifiers currently associated with this instance. List of VLAN EXEC User EXEC Spanning Tree Adminmode Enabled or disabled. Spanning Tree Version Version of 802.1 currently supported - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 107
Reference for the ProSafe 7200RS Series show spanning-tree interface Modes Privileged EXEC User EXEC Hello Time Admin hello time for this port. Port mode Port Up Time Since Counters Last Cleared Time since port was reset, displayed in days, hours, minutes, and seconds. STP - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 108
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches MSTP BPDUs . Format show spanning-tree mst port detailed Mode Privileged EXEC User EXEC MST Instance ID The ID of the existing MST instance. Port Identifier The port identifier - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 109
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Designated Designated Bridge that offers the lowest cost to the LAN. If you specify 0 (defined as the default CIST ID) as the , this command displays the settings and parameters for a specific switch - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 110
for the ProSafe 7200RS Series desired switch port or all ports. If you specify 0 (defined as the default CIST ID) as the , the status summary displays for one or mstid> { | all} Modes Privileged EXEC User EXEC MST Instance ID The MST instance associated with this port. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 111
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches MST Instance ID List For each MSTID: Associated FIDs Associated VLANs List of to an existing VLAN ID. Format show spanning-tree vlan Modes Privileged EXEC User EXEC VLAN Identifier The VLANs associated with the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 112
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 5-18 Spanning Tree Protocol Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 113
switch settings, statistics, and other information. • Configuration commands configure features and options of the switch. For every configuration command, there is a show command that displays the configuration setting. 6.1 VLAN Configuration Commands This section describes the commands you use to - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 114
no network mgmt_vlan Mode Privileged EXEC 6.1.4 vlan This command creates a new VLAN and assigns it an ID. The ID is a valid VLAN identification number (ID 1 is reserved for the default VLAN). VLAN range is 1-4093. Format vlan Mode VLAN Config 6-2 VLAN Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 115
number (ID 1 is reserved for the default VLAN). The VLAN range is 1-4093. Format no vlan Mode VLAN Config 6.1.5 vlan acceptframe This command sets the frame acceptance mode per interface. For VLAN Only mode, untagged frames or priority frames received on this interface are discarded - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 116
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 6.1.6.1 no vlan ingressfilter This command disables ingress filtering. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving interface are - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 117
acceptance mode for all interfaces. The modes defined as follows: • VLAN Only mode - Untagged frames or priority frames received on this interface are discarded. • Admit All mode - Untagged frames or priority frames received on this interface are accepted and assigned the value of the interface - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 118
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches With either option, VLAN tagged frames are forwarded in accordance with the IEEE 802.1Q VLAN Specification. Default all Format vlan port acceptframe all {vlanonly | all} Mode Global Config 6.1.11.1 no - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 119
for all ports. If ingress filtering is disabled, frames received with VLAN IDs that do not match the VLAN membership of the receiving interface are admitted and forwarded to ports that are members of that VLAN. Default disabled Format vlan port ingressfilter all Mode Global Config 6.1.14.1 no - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 120
ProSafe 7200RS Series Layer-2 Stackable Switches 6.1.16 vlan protocol group add protocol This command adds the to the protocol-based VLAN are ip, arp, and ipx. Default none Format vlan protocol group add protocol Mode Global Config 6.1.16.1 no vlan protocol - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 121
for the ProSafe 7200RS Series Layer-2 Stackable Switches 6.1.18.1 no protocol group This command removes the from this protocol-based VLAN group that is identified by this . Format no protocol group Mode VLAN Config 6.1.19 protocol vlan group This - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 122
it will be tagged with the PVID value as the VLAN ID for further processing. By default, every port belongs to VLAN 1 and the PVID value is set to 1. Default 1 Format vlan pvid Mode Interface Config 6.1.21.1 no vlan pvid This command sets the VLAN ID per interface to 1. Format no - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 123
It can be up to 32 alphanumeric characters long, including blanks. The default is blank. VLAN ID 1 always has a name of "Default." This field is optional. VLAN Type Type of VLAN, which can be Default (VLAN ID = 1) or static (one that is configured and permanently defined), or Dynamic (one that is - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 124
. This is equivalent to registration normal in the IEEE 802.1Q standard. Select the tagging behavior for this port in this VLAN. Tagged - specifies to transmit traffic for this VLAN as tagged frames. Untagged - specifies to transmit traffic for this VLAN as untagged frames. 6-12 v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 125
value must be for an existing VLAN. The factory default is 1. Acceptable Frame Types Specifies the types of frames that may be received on this port. The options are 'VLAN only' and 'Admit All'. When set to 'VLAN only', untagged frames or priority tagged frames received on this port are discarded - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 126
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches GVRP Default Priority this frame is associated. In a tagged frame, the VLAN is identified by the VLAN ID in the tag. In an untagged frame, the VLAN is the Port VLAN ID specified for the port that received - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 127
interface. Note: When you use the mode dvlan-tunnel command on an interface, it becomes a service provider port. Ports that do not have double VLAN tunneling enabled are customer ports. Default Format Mode disabled mode dvlan-tunnel Interface Config 6.3.3.1 no mode dvlan-tunnel This command is - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 128
[ | all] Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. Mode This field specifies the administrative mode through which Double VLAN Tunneling can be enabled or disabled. The default value for this field is disabled. EtherType - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 129
[ | all] Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. Mode This field specifies the administrative mode through which Double VLAN Tunneling can be enabled or disabled. The default value for this field is disabled. EtherType - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 130
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 6.4.1 vlan port priority all This command configuration setting. Format vlan port priority all Mode Global Config 6.4.2 vlan priority This command configures the default 802.1p port priority - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 131
TCP/ IP configurations. DHCP uses UDP as its transport protocol and supports a number of features that facilitate in administration address allocations. The DHCP Server Commands section includes the following topics: • Section • "Clear commands clear some or all of the settings to factory defaults - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 132
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 7.1 ip dhcp pool This command configures a DHCP address pool name on a DHCP server and enters DHCP pool configuration mode. Default none Format ip dhcp pool Mode Global Config Note: The CLI mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 133
-name This command removes the client name. Format no client-name Mode DHCP Pool Config 7.1.3 default-router This command specifies the default router list for a DHCP client. {address1, address2... address8} are valid IP addresses, each made up of four decimal bytes ranging from 0 to 255 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 134
Reference for the ProSafe 7200RS Series Layer-2 IP address and network mask for a manual binding to a DHCP client. Address and Mask are valid IP addresses; each made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.0 is invalid. The prefix-length is an integer from 0 to 32 Default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 135
for the ProSafe 7200RS Series Layer-2 Stackable Switches 7.1.7 lease This command configures the duration of the lease for an IP address that is IP address 0.0.0.0 is invalid. Mask is the IP subnet mask for the specified address pool. The prefix-length is an integer from 0 to 32. Default none - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 136
for the ProSafe 7200RS Series The specifies the domain name string of the client. Default none Format domain-name Mode DHCP Pool Config 7.1. NetBIOS Windows Internet Naming Service (WINS) name servers that are available to DHCP clients. One IP address is required, although - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 137
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 7.1.11.1 no of a DHCP client. Address is the IP address of the next server in the boot process, which is typically a TFTP server. Default inbound interface helper addresses Format next-server - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 138
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Format Mode 0c / a3 4f 22 0c / a34f.220c.9fed Default none Format option {ascii string | hex [...] | ip [...]} Mode DHCP Pool Config - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 139
server from pinging pool addresses and sets the number of packets to 0. Default 0 Format no ip dhcp ping packets Mode Global Config 7.2.3 service dhcp This command enables the DHCP server. Default disabled Format service dhcp Mode Global Config DHCP Commands 7-9 v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 140
ProSafe 7200RS Series Layer-2 Stackable Switches 7.2.3.1 no service dhcp This command disables the DHCP server. Format no service dhcp Mode Global Config 7.2.4 ip address pool. Default disabled Format ip dhcp bootp automatic Mode Global Config 7.2.4.1 no ip dhcp bootp automatic - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 141
the addresses are deleted. is a valid IP address made up of four decimal bytes ranging from 0 to 255. IP address 0.0.0.0 is invalid. Default none Format clear ip dhcp binding {address | *} Mode Privileged EXEC 7.3.2 clear ip dhcp server statistics This command clears DHCP server - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 142
the addresses are displayed. Format show ip dhcp global configuration Modes Privileged EXEC User EXEC Service DHCP The field to display the the IP Address assigned to the client. DNS Servers The list of DNS servers available to the DHCP client Default Routers The list of the default routers - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 143
of the hardware platform. Host The IP address and the mask for a manual binding to a DHCP client. 7.3.7 show ip dhcp server statistics This command displays DHCP server statistics. Format show ip dhcp server statistics Modes Privileged EXEC User EXEC Automatic Bindings The number of - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 144
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches DHCP RELEASE DHCP . If no IP address is specified, all the conflicting addresses are displayed. Format show ip dhcp conflict [ip-address] Modes Privileged EXEC User EXEC IP address The IP address of the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 145
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 7.4.1 ip dhcp relay information option This CPU's own MAC address). Default disabled Format ip dhcp relay information option Mode Global Config 7.4.1.1 no ip dhcp relay information option This command - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 146
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 7.4.3 bootpdhcprelay maxhopcount This command configures the maximum allowable relay agent hops for BootP/DHCP Relay on the system. The parameter has a range of 1 to 16. Default 4 Format bootpdhcprelay maxhopcount - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 147
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 7.4.5 bootpdhcprelay serverip This command configures the server IP Address for BootP/DHCP Relay on the system. The parameter is an IP address in a 4-digit dotted decimal format. Default 0.0.0.0 Format bootpdhcprelay - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 148
ProSafe 7200RS Series Layer-2 Stackable Switches Packets Discarded Is the number of packets discarded. 7.4.7 bootpdhcprelay backup-serverip To configure the IP > no bootpdhcprelay backup-serverip Mode Global Config Default no bootpdhcprelay backup-serverip 7-18 v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 149
GARP VLAN Registration VLANS (by using GVMP) or multicast groups (by using GMRP). This section contains the following topics: • Section • "Configuration commands configure features commands configure features and options (or reregistering) membership for a VLAN or multicast group. This command has - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 150
to wait after receiving an unregister request for a VLAN or a multicast group before deleting the VLAN entry. This can be considered a buffer time service.time is 20 to 600 (centiseconds). The value 60 centiseconds is 0.6 seconds. Note: This command has an effect only when GVRP is enabled. Default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 151
Interface Reference for the ProSafe 7200RS Series Layer-2 seconds. Note: This command has an effect only when GVRP is enabled. Default Format Modes 1000 set garp timer leaveall Interface Config Global Privileged EXEC User EXEC GARP, GVRP, and GMRP Commands 8-3 v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 152
information, which allows GVRP to provide dynamic VLAN creation on trunk ports and automatic VLAN pruning. Note: If GVRP is disabled, the system does not forward GVRP messages. 8.2.1 set gvrp adminmode This command enables GVRP. Default disabled Format set gvrp adminmode Mode Privileged - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 153
{ | all} Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward service. There is an instance of this timer on a per-Port, perGARP participant basis. Permissible values are 20 to 600 centiseconds (0.2 to 6.0 seconds). The factory default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 154
Reference for the ProSafe 7200RS Series Layer are 200 to 6000 centiseconds (2 to 60 seconds). The factory default is 1000 centiseconds (10 seconds). Indicates the GARP Multicast all networking devices in the bridged LAN that support Extended Filtering Services. Note: If GMRP is disabled, the system - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 155
functionality is disabled on that interface. GARP functionality is subsequently reenabled if routing is disabled and port-channel (LAG) membership is removed from an interface that has GARP enabled. Default disabled Format set gmrp interfacemode Modes Interface Config Global Config 8.3.2.1 no - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 156
the ProSafe 7200RS before deleting the attribute. Current attributes are a VLAN or multicast group. This may be considered a service. There is an instance of this timer on a per-Port, perGARP participant basis. Permissible values are 20 to 600 centiseconds (0.2 to 6.0 seconds). The factory default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 157
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 8.3.4 show mac is displayed as 8 bytes. Type Displays the type of the entry. Static entries are those that are configured by the end user. Dynamic entries are added to the table as a result of a learning - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 158
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 8-10 GARP, GVRP, and GMRP Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 159
provides a detailed explanation of the security commands. The commands are divided into the following groups: • Configuration commands are used to configure features and options of the switch. For every configuration command there is a show command that will display the configuration setting. • Show - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 160
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Default Format Modes disabled port-security Global security max-dynamic This command resets the maximum of dynamically locked MAC addresses allowed on a specific port to its default value. Format no port- - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 161
resets the maximum of statically locked MAC addresses allowed on a specific port to its default value. Format no port-security max-static Mode Interface Config 9.1.4 port-security mac-address This command adds a MAC address to the list of statically locked MAC addresses. The is the VLAN - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 162
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 9.1.6 show port-security the Interface. Dynamic Limit Maximum dynamically allocated MAC Addresses. Static Limit Maximum statically allocated MAC Addresses. Violation Trap Mode Whether violation traps - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 163
Reference for the ProSafe 7200RS Series Layer and view stormcontrol configuration information. The storm-control feature measures traffic activity on the physical ports and blocks Low 10M 20 10 100M 5 2 1000M 5 2 Default Format Mode enabled storm-control broadcast Config Port-Based - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 164
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 9.2.1.1 no storm-control broadcast . The thresholds are defined in the same way as for broadcast. Default disable Format storm-control multicast all Mode Config 9.2.2.1 no storm-control multicast - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 165
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 9.2.3.1 no storm-control are defined the same as the ones for broadcast storm control in Global mode. Default enable Format storm-contol broadcast [] Mode Interface Config 9.2.4.1 no storm-control - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 166
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 9.2.5.1 no storm-control defined the same as the ones for broadcast storm control in Global mode. Default enable Format storm-control unicast [] Mode Interface Config 9.2.6.1 no storm-control - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 167
ProSafe factory default is disabled. 802.3x Flow Control Mode May be enabled or disabled. The factory default as protected. The protected port is a feature that has only local significance to the switch If the interface is configured as a member of LAG or a probed port, this command will take - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 168
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Default Format Mode unprotected switchport traffic to each others in the same VLAN group. The main application is to isolate a group of users from another without using VLAN. 9.4.1 switchport private-group This command is - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 169
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches By default, a port does not belong group cannot forward its egress traffic to any other members in the same group. By default, the mode is "community" mode that each member port can forward traffic to other - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 170
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 9.4.5 show Priviledged EXEC Interface Valid slot and port number separated by forward slashes. Port VLANID The VLAN ID associated with the port. Private Group ID Total number of private groups is 192. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 171
settings, statistics, and other information. • Configuration commands configure features and options of the switch. For every configuration command, there , and is from 1 to 31 alphanumeric characters. Default none Format snmp-server {sysname | location | contact < - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 172
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 10.1.2 snmp-server community any IP address. Otherwise, this value is ANDed with the mask to determine the range of allowed client IP addresses. The name is the applicable community name. Default 0.0.0.0 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 173
for the ProSafe 7200RS Series Layer-2 Stackable Switches 10.1.3.1 no snmp-server community ipaddr This command sets a client IP address for 's IP address for the client IP Address. A value of 0.0.0.0 will allow access from any IP address. The name is the applicable community name. Default 0.0.0.0 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 174
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 10.1.5.1 no snmp- Note: For other port security commands, see Section 9.1, "Port Security Commands". Default Format Mode disabled snmp-server traps violation Interface Config 10-4 v1.0, October 2008 SNMP - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 175
the ProSafe 7200RS Series Layer-2 Stackable Switches 10.1.8.1 no snmp-server traps violation This command disables the sending of new violation traps. Format no snmp-server traps violation Mode Interface Config 10.1.9 snmp-server traps This command enables the Authentication Flag. Default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 176
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 10.1.11 snmp- interface session. Default enabled Format snmp-server traps multiusers Mode Global Config 10.1.12.1 no snmp-server traps multiusers This command disables Multiple User traps. Format no - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 177
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 10.1.13.1 no Table. For more information, see Section 10.1.2 "snmp-server community" on page 2. Default snmpv2 Format snmptrap [snmpversion ] Mode Global Config 10.1.14.1 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 178
can be snmpv1 or snmpv2. Note: This command does not support a "no" form. Default Format Mode snmpv2 snmptrap snmpversion table must be unique. If you make multiple entries using the same IP address, the first entry is retained and processed. All duplicate entries - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 179
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 10.1.18 snmp trap link-status This command enables link status traps by interface. Note: This command is valid only - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 180
Reference for the ProSafe 7200RS Series Layer communities are supported. You can add, change, or delete communities. The switch does not have to be reset for changes of this table must contain a unique community name. Client IP Address An IP address (or portion thereof) from which this device will - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 181
ProSafe 7200RS Series Layer-2 Stackable Switches Client IP Mask Access Mode Status Subnet Mask is set to 0.0.0.0, an IP Address of 0.0.0.0 matches all IP addresses. The default value is 0.0.0.0 A mask to be ANDed with the requesting entity's IP address before comparison with IP supported to reset - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 182
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Authentication Flag Link Up/Down Flag Multiple Users Flag Spanning Tree Flag Broadcast Storm Flag DVMRP Traps OSPF Traps PIM Traps Can be enabled or disabled. The factory default is enabled. Indicates whether - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 183
two functional groups: • Configuration commands are used to configure features and options of the switch. For every configuration command there is network services only to and devices that are authorized and authenticated. 11.1.1 authentication login This command creates an authentication login list - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 184
or to the non configured user for any component • The login list is the default login list included with the default configuration and was not created using 'authentication login'. The default login list cannot be deleted. Format no authentication login Mode Global Config 11-2 Port - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 185
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 11.1.2 clear dot1x statistics This command resets the 802.1x statistics for the authentication login list assigned to a specific user if the user is configured locally. If this value is not configured, users will be - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 186
of times the authenticator state machine on this port will transmit an EAPOL EAP Request/Identity frame before timing out the supplicant. The value must be in the range 1 - 10. Default 2 Format dot1x max-req Mode Interface Config 11.1.7.1 no dot1x max-req This command sets - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 187
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 11.1.8.1 no of the authentication exchanges between the supplicant, authenticator and the authentication server. Default auto Format dot1x port-control all {force-unauthorized | force-authorized | auto - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 188
ProSafe 7200RS Series Layer-2 Stackable Switches 11.1.11 dot1x re-authentication This command enables re-authentication of the supplicant for the specified port. Default to enable the dot1x authentication support on the switch. By default, the authentication support is disabled. While disabled, - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 189
for the ProSafe 7200RS Series machine on this port to determine when to send an EAPOL EAP Request/Identity frame to the supplicant. The quiet-period must be a value in the range timeout must be a value in the range 1 - 65535. Default reauth-period: 3600 seconds quiet-period: 60 seconds tx-period: - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 190
{macbased | portbased} Mode Interface Config Default portbased 11.1.15 dot1x user This command adds the specified user to the list of users with access to the specified port or all ports. The parameter must be a configured user. Format dot1x user { | all} Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 191
This command displays information about the users assigned to the specified authentication login list. If the login is assigned to non-configured users, the user "default" will appear in the user column. Format show authentication users Mode Privileged EXEC Port-Based Access and - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 192
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches User Component This field displays the user assigned to the specified authentication login list. This field displays the component (User or 802.1x) for which the authentication login list is assigned. 11.1.20 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 193
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Protocol by the authenticator state machine on the specified port to determine when to send an EAPOL EAP Request/Identity frame to the supplicant. The value, in seconds, has a range of 1 - 65535. The timer used - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 194
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Reauthentication Period frame. Last EAPOL Frame Source The source MAC address carried in the most recently received EAPOL frame. EAP Response/Id Frames Received The number of EAP response/identity frames - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 195
displays the authentication login list assigned to the default user. Format show users authentication Mode Privileged EXEC User Lists every user that has an authentication login list assigned. System Login Displays the authentication login list assigned to the user for system login. 802.1x - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 196
User Service (RADIUS) server on your network for authentication and accounting. 11.2.1 radius accounting mode Use this command to enable the RADIUS accounting function. Default you use the parameter, the command configures the IP address to use to connect to a RADIUS authentication server. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 197
for the ProSafe 7200RS Series Layer-2 Stackable Switches If you use the parameter, the command configures the IP address to in the range 1 - 65535, with 1813 being the default. Note: To re-configure a RADIUS accounting server to use the default UDP , set the parameter to 1813. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 198
Reference for the ProSafe 7200RS Series Layer-2 client. The primary server is the one that is used by default for handling RADIUS requests. The remaining configured servers are only used by the IP address specified used in this command will become the new primary server. The IP address must - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 199
ProSafe 7200RS Series Layer-2 Stackable Switches 11.2.6.1 no radius server retransmit This command sets the maximum number of times a request packet is re-transmitted, to the default [servers] Mode Privileged EXEC Primary Server IP Address Shows the configured server currently in use - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 200
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Timeout Duration Accounting and the RADIUS accounting server details are displayed. Mode Enabled or disabled IP Address The configured IP address of the RADIUS accounting server. Port The port in use by - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 201
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Round Trip Time Requests for RADIUS or configured server. To show the configured RADIUS server statistic, the IP Address specified must match that of a previously configured RADIUS server. On execution, the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 202
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches If you do not specify an IP address, then only the Invalid Server Address field is displayed. Otherwise other listed fields are displayed. Invalid Server Addresses The number of RADIUS Access-Response - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 203
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Pending reset the NAS-IP address for the RADIUS server. Format no radius server attribute 4 Mode Global Config 11.3.3 authorization network radius This command is used to enable the switch to accept vlan - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 204
ProSafe 7200RS Series Layer-2 Stackable Switches 11.3.4 no authorization network radius This command is used to disable the switch to accept vlan authentication, authorization, and accounting services. The original protocol was mode. The parameter is the IP address or hostname - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 205
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 11.4.3 tacacs-server Global Config 11.4.6 no tacacs-server timeout This command is used to restore the default timeout value for all TACACS servers. Format no tacacs-server timeout Mode Global Config - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 206
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 11.4.7 key This display the configuration and statistics of a TACACS+ server. Format show tacacs Mode Privileged EXEC 11-24 Port-Based Access and Authentication Commands v1.0, - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 207
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches IP-Address| Hostname Port Timeout Priority Port The IP address or the DNS name of the configured TACACS+ server. range from 0 to 65535 connection timeout range from 0 to 65535 range from 0 to 65535 Port- - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 208
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 11-26 Port-Based Access and Authentication Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 209
load sharing. The LAG feature initially load shares traffic based upon factory defaults. 12.1 Port-Channel Configuration Commands This section describes the commands you use to configure port-channels. Assign the LAG VLAN membership after you create a LAG. If you do not assign VLAN membership, the LAG - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 210
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 12.1.1 addport This command adds one port to the port-channel (LAG). The first interface is a logical unit, slot and port number of a configured port-channel. Note: Before adding a port to a port-channel, set - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 211
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 12.1.4.1 no port-channel This command deletes a port-channel (LAG). Format no port- Link Aggregation Control Protocol (LACP) on a port. Default enabled Format port lacpmode Mode Interface Config 12.1.6.1 no - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 212
for the ProSafe 7200RS Series Layer-2 Stackable Switches 12.1.8 port-channel adminmode This command enables a port-channel (LAG). The administrative mode setting. Default enabled Format port-channel linktrap { | all} Mode Global Config 12-4 Port-Channel/LAG (802.3ad) - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 213
port ID 2. Destination MAC, VLAN, EtherType, and port ID 3. Source IP and source TCP/UDP port 4. Destination IP and destination TCP/UDP port 5. Source/Destination MAC, VLAN, EtherType and port 6. Source/Destination IP and source/destination TCP/UDP port Default 3 Format hashing-mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 214
for the ProSafe 7200RS Series Layer-2 Stackable Switches 12.2.1 show port-channel This command displays the static capability of all port-channels (LAGs) on the device as well as a summary of individual port-channels. Format show port-channel Modes Privileged EXEC User EXEC Static Capability - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 215
ProSafe 7200RS Series Layer-2 Stackable Switches Mbr Ports Port Speed Type Active Ports Enable - Spanning tree is enabled for this port. A listing of the ports that are members of this port-channel (LAG (LAG) is statically or dynamically maintained. Static - The port-channel is statically - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 216
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 12-8 Port-Channel/LAG (802.3ad) Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 217
Policy Commands" on page 16 • Section 13.5 "DiffServ Service Commands" on page 21 • Section 13.6 "DiffServ Show (ACL) Commands" on page 29 • Section 13.8 "IP Access Control List (ACL) Commands" on page 33 The Configuration Commands are used to configure features and options of the switch. For - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 218
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches ip-precedence-mapping This command maps an IP precedence value to a default internal traffic class value Format no classofservice ip-precedence-mapping Modes Global Config Interface Config 13-2 Quality of Service - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 219
> Global Config 13.1.3.1 no classofservice ip-dscp-mapping This command maps an IP DSCP value to a default internal traffic class value. Format no classofservice ip-dscp-mapping Mode Global Config 13.1.4 classofservice trust This command sets the class of service trust mode of an interface - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 220
ProSafe 7200RS Series Layer-2 Stackable Switches 13.1.5 cos-queue min-bandwidth This command specifies the minimum transmission bandwidth guarantee for each interface queue. The total number of queues supported command restores the default for each queue's Service (QoS) Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 221
ProSafe 7200RS Series Layer-2 Stackable Switches Format Modes traffic-shape Global Config Interface Config 13.1.7.1 no traffic-shape This command restores the interface shaping rate to the default that support independent per-port class of service mappings. If specified, the IP Precedence - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 222
to which the IP DSCP value is mapped. 13.1.11 show classofservice trust This command displays the current trust mode setting for a specific interface. The unit/ slot/port parameter is optional and is only valid on platforms that support independent perport class of service mappings. If specified - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 223
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Format Mode Queue Id Minimum Bandwidth Scheduler Type Queue Management Type show interfaces cos-queue [unit/slot/port] Privileged EXEC An interface supports n queues numbered 0 to (n-1). The specific n value - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 224
Class definitions do not support hierarchical service policies A given class IP DSCP, and IP Precedence. While the latter two are only meaningful for IP packet types, CoS marking is allowed for both IP and non-IP packets, since it updates the 802.1p user priority field contained in the VLAN - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 225
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Format Mode diffserv Global uniquely identifying an existing DiffServ class. Note: The class-map-name 'default' is reserved and must not be used. Quality of Service (QoS) Commands v1.0, October 2008 13-9 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 226
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable class-map-name> is the name of an existing DiffServ class ( The class name 'default' is reserved and is not allowed here). This command may be issued at any time Map Config 13-10 Quality of Service (QoS) Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 227
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 13.3.4 match any This command adds to the specified class class definition. Format no match class-map Mode Class-Map Config Quality of Service (QoS) Commands v1.0, October 2008 13-11 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 228
Service value (the only tag in a single tagged packet or the first or outer 802.1Q tag of a double VLAN tagged packet). The value may be from 0 to 7. Default on the destination IP address of a packet. The parameter specifies an IP address. The parameter specifies an IP address bit - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 229
cs3, cs4, cs5, cs6, cs7, ef. Note: The ip dscp, ip precedence, and ip tos match conditions are alternative ways to specify a match criterion for the same Service Type field in the IP header, but with a slightly different user notation. Format Mode match ip dscp Class-Map Config 13.3.11 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 230
> value of a0 (hex) and a of a2 (hex). Note: The ip dscp, ip precedence, and ip tos match conditions are alternative ways to specify a match criterion for the same Service Type field in the IP header, but with a slightly different user notation. Note: This "free form" version of the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 231
ProSafe ff:07:23:ff:fe:dc). Default none Format match source-address mac - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 232
for the ProSafe 7200RS Series Layer-2 Stackable Switches The currently supported - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 233
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches The CLI command root is policy-map. To enter " queueid is an integer from 0 to n-1, where n is the number of egress queues supported by the device. Quality of Service (QoS) Commands v1.0, October 2008 13-17 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 234
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Format assign-queue Mode Policy-Class-Map Config causes the specified policy to create a reference to the class definition. 13-18 Quality of Service (QoS) Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 235
the ProSafe 7200RS packet or the first or outer 802.1Q tag of a double VLAN tagged packet). If the packet does not already contain this header, 7. Default 1 Format mark-cos Mode Policy-Class-Map Config Incompatibilities Drop, Mark IP DSCP, IP Precedence, Police Quality of Service ( - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 236
ProSafe 7200RS Series Layer-2 Stackable Switches 13.4.7 mark ip-dscp This command marks all packets for the associated traffic stream with the specified IP action defaults to transmit and the violate action defaults to , ef. For set-prec-transmit, an IP Precedence value is required. It is an - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 237
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Format Mode police-simple { - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 238
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Note: This DiffServ policy; it is defined by the Policy-Map command. Note: This command causes a service to remove its reference to the policy. This command effectively disables DiffServ on an interface - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 239
user. The fields are evaluated in accordance with the class type. The possible Match Criteria fields are: Destination IP Address, Destination Layer 4 Port, Every, IP DSCP, IP Precedence, IP TOS, Protocol Keyword, Reference Class,Source IP Quality of Service (QoS) Commands v1.0, October 2008 13-23 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 240
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Mode DiffServ Size Policy Instance Table Max Policy Attribute Table Size Policy Attribute Table Max Service Table Size Service Table Max Privileged EXEC The current value of the DiffServ administrative mode. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 241
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches If the Policy Name is specified the following fields are displayed: Policy Name The name of this policy. Type The policy type (Only inbound policy definitions are supported for this platform.) The following - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 242
ProSafe 7200RS Series Layer-2 Stackable Switches Mark IP DSCP Mark IP Precedence Non-Conform Action Denotes the mark/re-mark value used as the DSCP for traffic matching this class. This is not displayed if mark ip IP the IP supported). Class Members List of all class names associated with this - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 243
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 13.6.4 show diffserv service This command displays policy service information for the specified interface and direction. The parameter specifies a valid unit/slot/port number for the system. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 244
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches OperStatus Policy Name The current operational status of this DiffServ service interface. The name of the policy attached to the interface in the indicated direction. 13.6.6 show policy-map interface This - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 245
ProSafe operational status of this DiffServ service interface. Policy Name The name . MAC ACLs ensure that only authorized users have access to specific resources and block supports only Ethernet II frame types. • The maximum number of rules per IP ACL is hardware dependent. • If you configure an IP - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 246
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable configured rules for the list. Note: The 'no' form of this command is not supported since the rules within a MAC ACL cannot be deleted individually. Instead, you must 30 Quality of Service (QoS) Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 247
of the IP access list "match every" rule. Format Mode {deny|permit} {{ } | any} {{ } | any} [ | ] [vlan {eq }] [cos ] [[log] [assign-queue ]] Mac-Access-List Config Quality of Service (QoS) Commands - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 248
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 13.7.4 mac access-group This 'Interface Config' mode command is only available on platforms that support independent per-port class of service queue configuration. Format mac access-group in [sequence - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 249
you use to configure IP ACL settings. IP ACLs ensure that only authorized users have access to specific resources and block any unwarranted attempts to reach network resources. The following rules apply to IP ACLs: • The 7200RS Series Stackable Switch does not support IP ACL configuration for - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 250
tos/tosmask. The command specifies the TCP flags for an IP ACL rule depending on a TCP flag match. Supported options are: • URG (Urgent Pointer Flag)-identifies incoming data which packets matching this rule are assigned. Default none 13-34 Quality of Service (QoS) Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 251
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches IP Standard ACL: Format Mode IP Extended ACL: Format Mode access Default none Format ip access-group in [sequence ] Modes Interface Config Global Config Quality of Service - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 252
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 13.8.2.1 no ip access-group This command removes a specified IP ACL from an interface. Default none Format no ip access-group in Mode Interface Config 13.8.3 show ip access-lists This command - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 253
ProSafe 7200RS Series Layer-2 Stackable Switches 13.8.4 show access-lists This command displays IP list (IP or MAC). ACL ID Access List name for a MAC access list or the numeric identifier for an IP access the sequence number is not specified by the user, a sequence number that is one greater than - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 254
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 13-38 Quality of Service (QoS) Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 255
-1. Exceptions to Feature Support Among the 7200RS Series Switches Commands Documente d in Chapter Switch Model FSM726E FSM7226RS FSM7250RS GSM7224R GSM7248R Routing 14 Stacking 16 on the switch. ARP associates IP addresses with MAC addresses and stores the information as ARP entries in - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 256
. The device only responds if all next hops in its route to the destination are through interfaces other than the interface that received the ARP request. Default enabled Format ip proxy-arp Mode Interface Config 14.1.2.1 no ip proxy-arp This command disables proxy ARP on a router interface - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 257
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.1.3 arp cachesize positive integer, which represents the IP ARP entry response timeout time in seconds. The range for is between 1-10 seconds. Default l Routing Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 258
ProSafe 7200RS Series Layer-2 Stackable Switches Format Mode arp resptime Global Config 14.1.6.1 no arp resptime This command configures the default which represents the IP ARP entry ageout time in seconds. The range for is between 15-21600 seconds. Default 1200 Format arp - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 259
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.1.9 table. Field listing the static entry count in the ARP table and maximum static entry count in the ARP table. The following fields are displayed for each ARP entry. Routing Commands v1.0, October 2008 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 260
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches IP Address MAC Address Interface Type Age Is the IP address of a device on a subnet attached to an existing routing interface. Is the hardware MAC address of that device. Is the routing unit/slot/port associated with - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 261
. You can view the current value for this function with the show ip command. The value is labeled as "Routing Mode." Default disabled Format routing Mode Interface Config 14.2.1.1 no routing This command disables routing for an interface. You can view the current value for this function - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 262
whether a static route is more or less preferred than other static routes to the same destination. The following must be present before the static routes are visible: • Enable ip routing globally. • Enable ip routing for the interface. • The associated link must also be up. Default preference - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 263
route is reset to its default. Format no ip route default [{ | }] Mode Global Config 14.2.6 ip route distance This command sets the default distance for static routes. Lower route preference values are preferred when determining the best route. The ip route and ip route - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 264
ip route distance This command sets the default static route preference value in the router. Lower route preference values are preferred when determining the best route. Format no ip route distance Mode Global Config 14.2.7 ip forwarding This command enables forwarding of IP frames. Default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 265
for the packet. Acceptable values for are ethernet and SNAP. The default is ethernet. Format encapsulation {ethernet | snap} Mode Interface Config Note: Routed frames are always ethernet encapsulated when a frame is routed to a VLAN. Routing Commands v1.0, October 2008 14-11 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 266
show ip Modes Privileged EXEC User EXEC Default Time to Live The computed TTL (Time to Live) of forwarding a packet from the local router to the final destination. Routing Mode Shows whether the routing mode is enabled or disabled. IP Forwarding Mode Shows whether forwarding of IP frames is - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 267
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.2.12 show ip interface This command displays all pertinent information about the IP interface. Format show ip interface Modes Privileged EXEC User EXEC Primary IP Address Displays the primary - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 268
in the router. Format show ip interface Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. IP Address The IP address of the routing interface in 32-bit dotted decimal format. IP Mask The IP mask of the routing interface in 32-bit dotted - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 269
of the network and host portion of the IP address for the specified interface. Protocol Tells which protocol added the specified route. The possibilities are: local, static, OSPF or RIP. Total Number of Routes The total number of routes in the route table. The following information displays for - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 270
values are preferred over higher router preference values. Format show ip route preferences Modes Privileged EXEC User EXEC Local This field displays the local route preference value. Static This field displays the static route preference value. OSPF Intra This field displays the OSPF - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 271
> value has a range from 1 to 4093. Format no vlan routing Mode VLAN Config 14.3.2 show ip vlan This command displays the VLAN routing information for all VLANs with routing enabled. Format show ip vlan Modes Privileged EXEC User EXEC Routing Commands v1.0, October 2008 14-17 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 272
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches MAC Address used by Routing VLANs VLAN ID Logical Interface IP Address Subnet Mask Is the MAC Address associated with the internalbridge-router interface (IBRI). The same MAC Address is used by all VLAN routing interfaces. It will - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 273
address as a secondary IP address on an interface. Default enabled Format ip vrrp [secondary] Mode Global Config 14.4.2.1 no ip vrrp This command disables the default administrative mode of VRRP in the router. Format no ip vrrp Mode Global Config Routing Commands v1 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 274
ProSafe 7200RS Series Layer-2 Stackable Switches 14.4.3 ip 255. Default none Format ip vrrp ip Mode Interface Config 14.4.5 ip vrrp password. The parameter is the virtual router ID which has an integer value ranges from 1 to 255. Default no authorization Format ip - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 275
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.4.5.1 no ip vrrp authentication This command sets the default authorization details value for the virtual router configured on a specified interface. Format no ip vrrp authentication Mode Interface - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 276
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.4.8 ip vrrp timers advertise This command sets the frequency, in seconds, that an interface on the specified virtual router sends a virtual router advertisement. Default 1 Format ip vrrp timers advertise - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 277
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Authentication Failure IP TTL errors Zero Priority Packets Received Zero Priority Packets Sent packets received with packet length less than length of VRRP header. Routing Commands v1.0, October 2008 14-23 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 278
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.4.10 show ip vrrp This command displays whether It displays information about each virtual router. Format show ip vrrp interface Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 279
Format show ip vrrp interface Modes Privileged EXEC User EXEC IP Address This field represents the configured IP Address use to view and configure OSPF, which is a link-state routing protocol that you use to route traffic within a network. Note: The OSPF command is not - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 280
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.1 router ospf Use this command to enter Router OSPF mode. Format router ospf Mode Global Config 14.5.2 enable (OSPF) This command resets the default administrative mode of OSPF in the router ( - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 281
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.4 1583compatibility This command enables OSPF 1583 compatibility. Note: 1583 compatibility mode is enabled by default. If all OSPF routers in the routing domain are capable of operating according to RFC - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 282
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.7 area nssa default-info-originate This command configures the metric value and type for the default route advertised into the NSSA. The optional metric parameter specifies the metric of the default route and is to - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 283
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches a specified area range for a specified NSSA. The is a valid IP address. The is a valid subnet mask. The LSDB type must be Router OSPF Config Routing Commands v1.0, October 2008 14-29 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 284
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches identified by . The Summary LSA mode is configured as enabled. Default disabled Format area stub summarylsa Mode Router OSPF Config 14 Config 14-30 v1.0, October 2008 Routing Commands - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 285
ProSafe specified.The default value for authentication type is none. Neither the default password key nor the default key id are configured. Default none Format 65535. Default 40 Format area virtual-link dead-interval Mode Router OSPF Config Routing Commands v1 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 286
ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.17.1 no area virtual-link dead-interval This command configures the default seconds> is 1 to 65535. Default 10 Format area virtual command configures the default hello interval for is 0 to 3600. Default 5 Format area - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 287
-link transmitdelay Mode Router OSPF Config 14.5.21 default-information originate (OSPF) This command is used to control the advertisement of default routes. Default metric - unspecified; type - 2 Format default-information originate [always] [metric ] [metric-type - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 288
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.21.1 no default-information originate (OSPF) This command is used to control the advertisement of default routes. Format no default-information originate [metric] [metrictype] Mode Router OSPF Config - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 289
ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.24 distribute-list out Use this command to specify the access list to filter routes received from the source protocol. Format distribute-list out {rip | static the router to again originate non-default AS-external-LSAs. When set to - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 290
ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.26 external-lsdb-limit This command configures the external LSDB limit for OSPF. If the value is -1, then there is no limit. When the number of non-default default values. Format ip ospf areaid Mode Interface Config 14.5.28 ip - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 291
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Format Mode ip ospf authentication {none | {simple } | {encrypt }} Interface Config 14.5.28.1 no ip ospf authentication This command sets the default OSPF Authentication Type for the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 292
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.30.1 no ip ospf dead-interval This command sets the default OSPF dead interval for the specified interface. Format no ip ospf dead-interval Mode Interface Config 14.5.31 ip ospf hello-interval This command - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 293
3600 (1 hour). Default 1 Format ip ospf transmit-delay Mode Interface Config 14.5.34.1 no ip ospf transmit-delay This command sets the default OSPF Transit Delay for the specified interface. Format no ip ospf transmit-delay Mode Interface Config Routing Commands v1.0, October - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 294
This command configures OSPF protocol to allow redistribution of routes from the specified source protocol/routers. Default metric - unspecified; type - 2; tag - 0 Format redistribute {rip | static | connected} [metric ] [metric-type {1 | 2}] [tag ] [subnets] Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 295
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.37.1 no redistribute This command configures OSPF protocol to prohibit redistribution of routes from the specified source protocol/routers. Format no redistribute {rip | static | connected} [metric] [metric-type - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 296
ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.40 show ip ospf This command displays information relevant to the OSPF router. Format show ip ospf Mode Privileged EXEC Note: Some of the information below displays only if you enable OSPF and configure certain features routes learnt - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 297
ProSafe 7200RS Series Layer-2 Stackable Switches New LSAs Originated LSAs Received External LSDB Limit Default Metric Default Route /routes that are being redistributed. Possible values are static, connected, or RIP. Shows the metric of the routes being redistributed. Shows whether the routes - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 298
ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.41 show ip ospf area This command displays information about the area. The identifies the OSPF area that is being displayed. Format show ip ospf area Modes Privileged EXEC User area route the Default Metric Type for - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 299
the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.42 show ip not grouped by area. Format show ip ospf database Modes Privileged EXEC User EXEC Note: The information below is during routing calculations. Router Options are valid for router links only. 14.5.43 show ip ospf interface - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 300
/port> This command displays the information for the IFO object or virtual interface tables. Format show ip ospf interface Modes Privileged EXEC User EXEC IP Address Represents the IP address for the specified interface. Subnet Mask A mask of the network and host portion of - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 301
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Router Priority Retransmit Interval Hello Interval Dead Interval LSA Ack Link Events The number of link events. Metric Cost The cost of the OSPF interface. Routing Commands v1.0, October 2008 14-47 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 302
only be displayed if OSPF is enabled. Format show ip ospf interface stats Modes Privileged EXEC User EXEC OSPF Area ID The area id of this OSPF interface. Spf Runs The number of times that the intra-area route table has been calculated using this area's link-state database - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 303
for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.46 show ip ospf neighbor This command displays the OSPF neighbor table list. The information below is displayed only if OSPF is enabled. Format show ip ospf neighbor { | all} Modes Privileged EXEC User EXEC Router - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 304
Format show ip ospf neighbor Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes.. Router Id Is a 4-digit dotted-decimal number identifying neighbor router. Options Indicates the optional OSPF capabilities supported by - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 305
ProSafe . 14.5.48 show ip ospf range User EXEC Area ID The area id of the requested OSPF area. IP Address An IP Address which represents this area range. Subnet Mask A valid subnet mask for this area range. Lsdb Type The type of link advertisement associated with this area range. Routing - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 306
stub metric. The 7200RS Series Stackable Switch only supports Normal TOS. Metric Val The metric value is applied based on the TOS. It defaults to the least metric of the type of service among the interfaces to other areas. The OSPF cost for a route is a function of the metric value. Metric Type - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 307
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.5.51 show ip ospf virtual-link < neighbor's Router ID. Format show ip ospf virtual-link Modes Privileged EXEC User EXEC Area ID The area id state. Routing Commands v1.0, October 2008 14-53 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 308
RIP, which is a distance-vector routing protocol that you use to route traffic within a small network. 14.6.1 router rip Use this command to enter Router RIP mode. Format router rip Mode Global Config 14.6.2 enable (RIP) This command resets the default administrative mode of RIP in the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 309
is used to set a default for the metric of distributed routes. Format default-metric Mode Router RIP Config 14.6.6.1 no default-metric (RIP) This command is used to reset the default metric of distributed routes to its default value. Format no default-metric Mode Router RIP Config - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 310
RIP Config 14.6.8 distribute-list out This command is used to specify the access list to filter routes received from the source protocol. Default 0 Format distribute-list out {ospf | static | connected} Mode Router RIP Config 14.6.8.1 no distribute-list out This command is used to - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 311
for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.6.9 ip rip authentication This ip rip receive version This command configures the interface to allow RIP control packets of the default version(s) to be received. Format no ip rip receive version Mode Interface Config Routing - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 312
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 14.6.11 ip rip send version This command control packets to be sent. Default rip2 Format ip rip send version {rip1 | rip1c | rip2 | none} Mode Interface Config 14.6.11.1 no ip rip send version This command - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 313
ProSafe 7200RS Series Layer-2 Stackable Switches 14.6.13 split-horizon This command sets the RIP split horizon mode. Default redistributed. Internal routes are redistributed by default. Default metric - not routes from the specified source protocol/routers. Format no redistribute {ospf | static - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 314
relevant to the RIP router. Format show ip rip Modes Privileged EXEC User EXEC RIP Admin Mode Enable or disable. Split Horizon Mode None, simple or poison reverse. Split horizon is a technique for avoiding problems caused by including routes in updates sent to the router from which - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 315
. For this command to display successful results routing must be enabled per interface (i.e. ip rip). Format show ip rip interface Modes Privileged EXEC User EXEC Interface Valid slot and port number separated by forward slashes. IP Address The IP source address used by the specified RIP - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 316
Type for the specified interface. The types are none, simple, and encrypt. This is a configured value. Default Metric A number which represents the metric used for default routes in RIP updates originated on the specified interface. This is a configured value. The following information will be - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 317
supports IGMP Versions 1, 2, and 3. The IGMP snooping feature can help conserve bandwidth because it allows the switch to forward IP to Feature Support Among the 7200RS Series Switches Commands Documente d in Chapter Switch Model FSM7226 FSM7226RS FSM7250RS GSM7224R GSM7248R Routing 14 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 318
interface. IGMP Snooping functionality is re-enabled if you disable routing or remove port-channel (LAG) membership from an interface that has IGMP Snooping enabled. The IGMP application supports the following activities: • Validation of the IP header checksum (as well as the IGMP header checksum - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 319
functionality is re-enabled if you disable routing or remove port-channel (LAG) membership from an interface that has IGMP Snooping enabled. Default disabled Format ip igmpsnooping interfacemode Mode Global Config 15.1.2.1 no ip igmpsnooping interfacemode This command disables IGMP Snooping - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 320
This command sets the IGMP Maximum Response time (on the interface or VLAN) to the default value. Format no ip igmpsnooping maxresponse Modes Global Config Interface Config VLAN Mode 15.1.5 ip igmpsnooping mcrtexpiretime This command sets the Multicast Router Present Expiration time. The - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 321
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 15.1.5.1 no ip igmpsnooping mcrtexpiretime This command sets the Multicast Router Present Expiration time to 0. The time is set for the system, on a particular interface or a VLAN. Format no ip igmpsnooping mcrtexpiretime - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 322
ProSafe 7200RS Series Layer-2 Stackable Switches 15.1.7.1 no ip igmp mrouter interface This command disables the forwarding of IGMP packets to a multicast router via this interface. Format no ip igmp mrouter interface Mode Interface Config 15.1.8 ip the same VLAN. Format no ip igmpsnooping - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 323
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Admin Mode Interfaces Enabled for IGMP Snooping Multicast Control Frame Count VLANS Enabled for IGMP Snooping This indicates whether or not IGMP Snooping is active on the switch. This is the list of - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 324
ProSafe 7200RS Series Layer-2 Stackable Switches When you specify a value for , the following additional information appears: VLAN Admin Mode Indicates whether IGMP Snooping is active on the VLAN. 15.2.2 show ip igmp mrouter interface This command displays information about statically - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 325
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Type Description Interfaces displayed as a MAC address and VLAN ID combination of 8 bytes. Displays the type of the entry, which is either static (added by the user) or dynamic (added to the table as a result - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 326
it is executed (global or per VLAN). The is the VLAN where IGMP querier will be sent. Format [no] ip igmpsnooping querier [] Mode Global Config, VLAN Database Default Disabled 15.3.2 ip igmpsnooping querier ip-address To configure the IP address used by the IGMP - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 327
. Valid range for is 1 to 18000 seconds. must be a defined VLAN. Format [no] ip igmpsnooping querier query-interval Mode Global Config Default interval, 60 15.3.4 show ip igmpsnooping querier To display IGMP querier configuration information use show - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 328
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 15-12 v1.0, October 2008 IGMP Snooping Commands - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 329
section are in one of two functional groups: • Show commands display switch settings, statistics, and other information. • Configuration commands configure features and options of the switch. For every configuration command, there is a show command that displays the configuration setting. Note: The - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 330
ProSafe 7200RS Series Layer-2 Stackable Switches 16.1.2 member This command configures a switch. The is the switch identifier of the switch to be added/removed from the stack. The is the index into the database of the supported supported switchtype command in User defaults - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 331
Reference for the ProSafe 7200RS Series Layer-2 before performing the stack move. A stack move causes all routes and layer 2 addresses to be lost. This command is is loaded on all switches in the stack. Switch(es) must be reset for the new code to start running. Format archive copy-sw < - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 332
be deleted and the slot will be re-configured with default information for the card. Format slot Mode Global Config Note: Card index can be obtained by executing show supported cardtype command in User EXEC mode. 16.1.8.1 no slot This command removes configured - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 333
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 16.1.9 set slot disable This command configures the administrative mode of the slot(s). If you specify [all], the command is - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 334
the ProSafe 7200RS Series identifier. The system prompts you to confirm that you want to reset the switch. Format reload [unit] Mode Global Config 16.1.12 show for a specific slot. Format show slot [unit/slot/port] Mode User EXEC Slot The slot identifier in a format. - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 335
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Power Down This field indicates information about all card types or specific card types supported in the system. Format show supported cardtype [cardindex] Mode User EXEC If you do not supply a value for - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 336
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 16.1.14 show switch This command displays information about all units in the stack or a single unit when you specify - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 337
ProSafe memory on the switch. This code executes after the switch is reset. If the switch is not present and the data is supported switchtype This commands displays information about all supported switch types or a specific switch type. Format show supported switchtype [switchindex] Mode User - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 338
ProSafe 7200RS Series Layer-2 Stackable Switches If you do not supply a value for [switchindex], the following output appears: Switch Index (SID) This field displays the index into the database of supported port to either stack or ethernet mode. Default Format Mode stack stack-port - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 339
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 16.2.2 qos-mode This command enables QOS mode for front panel stacking. Default enabled Format qos-mode Mode Stack Global Config 16.2.2.1 no qos-mode This command disables QOS mode for front panel - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 340
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 16.2.4 show stack-port counters This command displays summary data counter information for all interfaces. Format show stack-port counters - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 341
Format lldp transmit Mode Interface Config 17.1.2 no lldp transmit This command is used to return the local data transmission capability to the default. Format no lldp transmit Mode Interface Config 17.1.3 lldp receive This command is used to enable the LLDP receive capability. The command - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 342
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Format Mode lldp receive Interface Config 17.1.4 no lldp receive This command is used to return the reception of LLDPDUs to the default. Format no lldp receive Mode Interface Config 17.1.5 lldp timers - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 343
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 17.1.8 no lldp transmit-tlv This command is used to remove an optional TLV from the LLDPDUs. Use the command - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 344
-interval This command is used to return the notification interval to the default value. Format no lldp notification-interval Mode Global Config 17.1.15 clear lldp statistics Use this command to reset all LLDP statistics, including MED-related information. Format clear lldp statistics Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 345
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 17.1.18 show lldp interface This command displays a summary of the current LLDP configuration for a specific interface or for all - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 346
for the ProSafe 7200RS Series Layer-2 Stackable Switches Transmit Total Receive Total Discards Errors Ageouts TVL Discards TVL Unknowns TVL MED TVL 802.1 TVL 802.3 Total number of LLDP packets transmitted on the port. Total number of LLDP packets received on the port. Total number of LLDP frames - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 347
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Mode Local Interface Chassis ID Subtype Chassis ID Port ID Subtype Port ID System Name System Description Port Description System Capabilities Supported System Capabilities Enabled Time To Live Privileged - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 348
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 17.1.23 show by identifying the system name and versions of hardware, operating system, and networking software supported in the device. Describes the port in an alpha-numeric format. Indicates the primary - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 349
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 17.2 LLDP-MED Commands 17.2.1 lldp med This command is used to enable the MED of LLDP advertise capability. The - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 350
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 17.2.4 no lldp med confignotification This command is used to disable notifications. The 'all' option is also available in the - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 351
ProSafe 7200RS Series Layer-2 Stackable Switches 17.2.8 no lldp med faststartrepeatcount This command is used to the factory default value as Class I Generic [IP Communicatin Controller etc.], Class II Media Conference Bridge etc.], Class III Communication [IP Telephone etc.]. The fourth device - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 352
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches OperMED unknown. In this case, the VLAN ID, Priority and DSCP are ignored. Indicates if the policy type is using tagged or untagged VLAN. 17-12 Hardware Rev Firmware Rev Software Rev Serial Num Mfg - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 353
the ProSafe 7200RS I Generic [IP Communication Controller etc.], Class II Media [Conference Bridge etc.], Class III Communication [IP Telephone etc]). port> ] Mode Privileged EXEC Supported Capabilities Enabled Capabilities Device Class Shows the supported capabilities that was received in - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 354
ProSafe 7200RS Series Layer-2 Stackable Switches Media Application Type VLAN VLAN id, Priority and DSCP are ignored. Indicates if the policy type is using tagged or untagged VLAN. Hardware Revision Firmware Shows the remote device's PoE device type connected to this port. 17-14 v1.0, - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 355
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Available Source Priority Shows the romote port's PSE power value in tenths of a watt. Shows the remote port's PSE power - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 356
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 17-16 v1.0, October 2008 LLDP and LLDP-MED Commands - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 357
the switch. • Clear commands clear some or all of the settings to factory defaults. 18.1 System Information and Statistics Commands This section describes the commands you use to view information about system features, components, and configurations. 18.1.1 show arp switch This command displays - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 358
Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Mode MAC Address IP Address Interface Privileged EXEC A error messages from the system. The event log is not cleared on a system reset. The [unit] is the switch identifier. Format show eventlog [unit] Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 359
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Machine Model Serial Number FRU Number Part Number Maintenance Level Manufacturer Burned in MAC Address Software Version Operating System Network - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 360
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Packets Received Without Error Packets Received With Error Broadcast Packets Received Packets Transmitted Without Error Transmit Packets Errors Collisions Frames Time Since Counters Last Cleared The total - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 361
ProSafe 7200RS Series Layer-2 Stackable Switches Packets Transmitted Without Error Broadcast Packets Transmitted Transmit Packet Errors Address Entries Currently In Use VLAN static entries. The number of VLAN entries presently occupying the VLAN (excluding framing bits but including Frame Check - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 362
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches StatsPkts and including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets). Packets Received 128-255 Octets - The total number of - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 363
for the ProSafe 7200RS Series documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms. Fragments/Undersize Received - The total number of packets received that were less than 64 octets in length (excluding framing - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 364
half-duplex mode. Unacceptable Frame Type - The number of frames discarded from this port due to being an unacceptable frame type. VLAN Membership Mismatch - The number of frames discarded on this port due to ingress filtering. VLAN Viable Discards - The number of frames discarded on this port when - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 365
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Packets Transmitted Octets Upstream Threshold - The number of frames discarded due to lack of cell descriptors available for that packet's priority level. Total Bytes - The total number of octets of data ( - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 366
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Packets Transmitted Successfully Transmit Errors Transmit Discards Max Info - The maximum size of the Info (non-MAC) field that this port will receive or transmit. Total - The number of frames that have been transmitted - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 367
egress for this port due to egress filtering being enabled. VLAN Viable Discards - The number of frames discarded on this port when a lookup on a particular VLAN occurs while that entry in the VLAN table is being modified, or if the VLAN has not been configured. BPDU's received - The count of BPDU - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 368
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Dot1x Statistics Time Since Received - The total number of octets of data received by the processor (excluding framing bits but including FCS octets). Total Packets Received Without Error- The total number - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 369
have been active on this switch since the last reboot. Static VLAN Entries - The number of presently active VLAN entries on this switch that have been created statically. Dynamic VLAN Entries - The number of presently active VLAN entries on this switch that have been created by GVRP registration - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 370
Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Time Since Counters Last Cleared VLAN Deletes - The number of VLANs on this switch Privileged EXEC The number of traps that have occurred since the last reset. The number of traps that have occurred since the traps were last - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 371
Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable meanings of the values are: Static The value of the corresponding instance was added by the system or a user when a static MAC filter was defined. enabling VLANs for routing. System Maintenance Commands v1.0, October 2008 18-15 - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 372
ProSafe supported on the switch. This command displays/captures commands with settings/ configurations that differ from the default LAG or VLAN. The output captures how the configuration differs from the factory default value. Format show running-config interface {} | VLAN | LAG - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 373
ProSafe 7200RS Series Layer-2 Stackable Switches 18.1.11 terminal length This command controls the number of lines to be displayed when running the show running-config command. Format terminal length Mode Privileged EXEC 18.1.11.1 terminal no length This command resets factory default - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 374
ProSafe 7200RS Series Layer-2 Stackable Switches 18.2 System Utility Commands This section describes the commands you use to help troubleshoot connectivity issues and to restore various configurations to their factory defaults. 18.2.1 traceroute Use the traceroute command to discover the routes - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 375
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 18.2.5 clear pass This command resets all user passwords to the factory defaults without powering off the switch. You are prompted to confirm that the password reset should proceed. Format clear pass Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 376
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Replace the < xmodem | ymodem | zmodem | tftp://// For TFTP, the parameter is the IP address of the server, is the path to the file, and is the name - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 377
ProSafe or resets the current IP workstation the switch is connected to through the default VLAN (VLAN 1), as long as there is a physical path between the switch and the workstation. The terminal interface sends three pings to the target station. Format ping Modes Privileged EXEC, User - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 378
for the ProSafe 7200RS Series Layer-2 Stackable Switches 18.2.13 reload This command resets the switch without powering it off. Reset means that when the log file reaches full capacity, logging stops. Default enabled Format logging buffered wrap Mode Privileged EXEC 18-22 v1.0, - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 379
Reference for the ProSafe 7200RS Series a host. You can configure up to eight hosts. The is the IP address of the logging host. The value is a port number from 1 warning (4), notice (5), informational (6), or debug (7). Default port - 514; level - critical; Format logging host - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 380
messages. The can be in the range from 1 to 65535. Default 514 Format logging port Mode Global Config 18.3.6.1 no logging port This command resets the local logging port to the default. Format no logging port Mode Global Config 18.3.7 logging syslog This command - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 381
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches Console Logging Administrative Mode Console Logging Severity Filter Buffered Logging Administrative Mode Buffered Logging Severity Filter Historical Logging Administrative Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 382
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 18.3.9 show logging buffered This command displays buffered logging (system startup and system operation logs). Format show logging buffered Mode - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 383
Logging. 18.4.1 logging cli-command This command enables the CLI command logging feature, which enables the 7200RS Series Stackable Switch software to log all CLI commands issued on the system. Default enabled Format logging cli-command Mode Global Config 18.4.1.1 no logging cli-command - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 384
for the ProSafe 7200RS Series systems with default configuration; however, you are not prevented from applying scripts on systems with non-default configurations. Script file for displaying the ip interface ! Display information about interfaces show ip interface 1/0/1 !Displays the information - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 385
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 18.5.1 script apply This command applies the commands in the script to the switch. The parameter is the name - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 386
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 18.6 Packet Capture Packet capture commands assist in troubleshooting protocol-related problems with the management CPU. The packets to and from the management CPU can be captured in an internally allocated - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 387
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 18.6.3 capture around to allow continuous packet caputure. Format capture wrap Mode Global Config Default Enabled 18.6.4.1 no capture all packets This command disables the Buffer Wrapping configuration - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 388
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 18.7 Dumping System Information The show tech-support command dumps all major system information into a file that can be sent to NETGEAR product support for debugging purposes. The command output is not - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 389
as IP helper) feature provides a mechanism that allows the switch to forward certain configured UDP broadcast packets to a particular IP Service (port 37) The system supports a maximum of 128 interface address-port pairs. For example, you can have a single UDP port forwarded on 128 different routing - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 390
relay BOOTP/DHCP packets, use the DHCP relay commands. Format ip helper-address {intf-address | all} ip-address [udpport-list] no ip helper-address {intf-address | all} ip-address Parameters Mode Default intf-address IP address of a routing interface. all Indicates that this UDP port to address - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 391
ProSafe 7200RS Series Layer-2 Stackable Switches 19.1.2 ip helper-address (interface config mode) The ip helper-address interface configuration command enables forwarding User to forward. If not specified, packets for the default services are forwarded to the helper address. Mode Interface Config - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 392
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 19-4 v1.0, October 2008 UDP Relay Commands - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 393
-policy show service-policy in show vlan brief show vlan copy nvram:msglog copy nvram:log remotecon maxsessions telnetcon maxsessions remotecon timeout telnetcon timeout vlan static vlan makestatic bootdhcprelay cidoptmode ip dhcp relay - Netgear GSM7248R | CLI Reference Manual - for 7200RS Series Layer-2 Stackable Sw - Page 394
Command Line Interface Reference for the ProSafe 7200RS Series Layer-2 Stackable Switches 3.0.3.4 Command set igmp maxresponse full-duplex set igmp 5.0.1.9 (or newer) Equivalent Command ip igmpsnooping maxresponse ip igmpsnooping minresponse snmp-server traps snmp-server traps
202-10455-01
October 2008
NETGEAR
, Inc.
350 Plumeria Dr.
San Jose, CA 95124 USA
Command Line Interface
Reference for the ProSafe
7200RS Series Layer-2
Stackable Switches with
Static Routing, Software
Version 7.3