Netgear MS2000 STORA User Manual - Page 25

Replacing a Failed Disk, Administration > Disk Management - support

Get Netgear MS2000 - Stora Media Center PDF manuals and user guides
UPC - 606449068184
View all Netgear MS2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

NETGEAR Stora User Manual Replacing a Failed Disk When a disk fails in your Stora device, you are notified of the failure by e-mail. On the front of the Stora device, an amber LED might indicate a failed disk. The top LED is disk 1; the bottom one is disk 2. Take note of the failed disk. To assure compatibility, check the Hardware Compatibility list on the NETGEAR support site for a list of disks qualified to be used in the Stora. WARNING! Be sure to power down the unit and then unplug Stora power cord before adding or removing the disks. Failure to observe this precaution by "hot-swapping" a drive could render your disks useless. To Eject a Disk 1. Open Stora application user interface. 2. Click Preferences. 3. Navigate to Administration > Disk Management 4. Click the Eject button. See "Disk Management" on page 106 for more information on ejecting disks. Figure 17 Safely eject a disk from your Stora Chapter 1: Getting Acquainted | 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Chapter 1:
Getting Acquainted
|
25
NETGEAR Stora User Manual
Replacing a Failed Disk
When a disk fails in your Stora device, you are notified of the failure by e-mail. On the front of
the Stora device, an amber LED might indicate a failed disk. The top LED is disk 1; the
bottom one is disk 2. Take note of the failed disk.
To assure compatibility, check the Hardware Compatibility list on the NETGEAR support site
for a list of disks qualified to be used in the Stora.
WARNING!
Be sure to power down the unit and then unplug Stora power cord
before adding or removing the disks. Failure to observe this
precaution by “hot-swapping” a drive could render your disks
useless.
To Eject a Disk
1.
Open Stora application user interface.
2.
Click Preferences.
3.
Navigate to
Administration > Disk Management
4.
Click the
Eject
button.
See
“Disk Management”
on page 106 for more information on ejecting disks.
Figure 17
Safely eject a disk from your Stora