Netgear WG602v3 WG602v3 User Manual - Page 23

Installing the WG602v3, Selecting Basic IP Settings Options, From your PC - ip address

Get Netgear WG602v3 - Wireless Access Point PDF manuals and user guides View all Netgear WG602v3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

NETGEAR 54 Mbps Wireless Access Point WG602v3 Reference Manual Installing the WG602v3 Before installing the NETGEAR WG602v3 54 Mbps Wireless Access Point, you should make sure that your Ethernet network is up and working. You will be connecting the access point to the Ethernet network so that computers with 802.11b or 802.11g wireless adapters will be able to communicate with computers on the Ethernet network. In order for this to work correctly, verify that you have met all of the system requirements, shown in "System Requirements" on page 2-2. To set up and install your wireless access point: 1. Prepare a computer with an Ethernet adapter. If this PC is already part of your network, record its TCP/IP configuration settings. 2. Turn on your computer and configure the PC with a static IP address of 192.168.0.210 and 255.255.255.0 for the Subnet Mask. 3. Connect an Ethernet cable from the WG602v3 to your PC. 4. Connect the power adapter to the WG602v3 and plug the power adapter into an AC outlet. Verify that • The Power power light goes on. • The Ethernet LED of the wireless access point is lit when connected to a powered on computer. • The Wireless LED should be blinking. Note: For detailed installation instructions, see the WG602v3 54 Mbps Wireless Access Point Installation Guide. Selecting Basic IP Settings Options To configure your basic IP settings: 1. From your PC, open a Web browser such as Internet Explorer, Netscape Navigator or Mozilla Firefox. 2. Enter http://192.168.0.227 into your browser window. http://192.168.0.227 Figure 2-1 Installation and Configuration 2-3 v1.0, August 2006

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
NETGEAR 54 Mbps Wireless Access Point WG602v3 Reference Manual
Installation and Configuration
2-3
v1.0, August 2006
Installing the WG602v3
Before installing the NETGEAR WG602v3 54 Mbps Wireless Access Point, you should make
sure that your Ethernet network is up and working. You will be connecting the access point to the
Ethernet network so that computers with 802.11b or 802.11g wireless adapters will be able to
communicate with computers on the Ethernet network. In order for this to work correctly, verify
that you have met all of the system requirements, shown in
“System Requirements” on page 2-2
.
To set up and install your wireless access point:
1.
Prepare a computer with an Ethernet adapter. If this PC is already part of your network, record
its TCP/IP configuration settings.
2.
Turn on your computer and configure the PC with a static IP address of 192.168.0.210 and
255.255.255.0 for the Subnet Mask.
3.
Connect an Ethernet cable from the WG602v3 to your PC.
4.
Connect the power adapter to the WG602v3 and plug the power adapter into an AC outlet.
Verify that
•
The Power power light goes on.
•
The Ethernet LED of the wireless access point is lit when connected to a powered on
computer.
•
The Wireless LED should be blinking.
Selecting Basic IP Settings Options
To configure your basic IP settings:
1.
From your PC, open a Web browser such as Internet Explorer, Netscape Navigator or Mozilla
Firefox.
2.
Enter http
:
//192.168.0.227 into your browser window.
Note:
For detailed installation instructions, see the
WG602v3 54 Mbps Wireless
Access Point Installation Guide
.
Figure 2-1