Nikon 9238 Super Coolscan LS5000 ED / Coolscan V ED User's Manual - Page 60

Inserting the Holder, Removing the Holder

Get Nikon 9238 - Super Coolscan 5000 ED PDF manuals and user guides
UPC - 018208092383
View all Nikon 9238 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Inserting the Holder 1 Insert the MA-21 slide-mount adapter After confirming that the status LED is not blinking, slide the MA-21 slide-mount adapter into the adapter slot ( 25). When the adapter is fully inserted, the status LED will blink while the scanner initializes ( 24). Wait until the status LED stops blinking. 2 Insert the FH-3 The direction of insertion depends on which of the two apertures in the metal cover contains the frame to be scanned; refer to the illustration below (arrows indicate direction of insertion). Slide the holder in until it stops. To scan frames 1-3, insert the left end of To scan frames 4-6, insert the right end of the holder into the scanner. the holder into the scanner. First frame scanned (frame "A"). Fourth frame scanned (frame "D"). Second frame scanned (frame "B"). Fifth frame scanned (frame "E"). Third frame scanned (frame "C"). Sixth frame scanned (frame "F"). Removing the Holder After confirming that the status LED is not blinking, remove the FH-3 by hand. The eject button on the MA-21 can not be used when removing the FH-3. Remove Film Holders Remove the FH-3 after use. Errors may occur if the FH-3 is in place when the scanner is turned on. If an error occurs, turn the scanner off and then on again after removing the FH-3. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
51
2
Insert the FH-3
The direction of insertion depends on which of the two
apertures in the metal cover contains the frame to be
scanned; refer to the illustration below (arrows indicate
direction of insertion).
Slide the holder in until it stops.
Inserting the Holder
1
Insert the MA-21 slide-mount adapter
After confirming that the status LED is not blinking, slide
the MA-21 slide-mount adapter into the adapter slot
(
25).
When the adapter is fully inserted, the status
LED will blink while the scanner initializes (
24).
Wait
until the status LED stops blinking.
To scan frames 1–3, insert the left end of
the holder into the scanner.
To scan frames 4–6, insert the right end of
the holder into the scanner.
Third frame
scanned (frame
“C”).
Second
frame scanned
(frame “B”).
First frame
scanned (frame
“A”).
Removing the Holder
After confirming that the status LED is not blinking, remove
the FH-3 by hand.
The eject button on the MA-21 can not
be used when removing the FH-3.
Remove Film Holders
Remove the FH-3 after use.
Errors may occur if the FH-3 is in place when the scanner is turned on.
If an
error occurs, turn the scanner off and then on again after removing the FH-3.
Fifth frame scanned
(frame “E”).
Fourth frame scanned
(frame “D”).
Sixth frame scanned
(frame “F”).