Onkyo HT-SP904 Owner Manual - Page 38

Using Audyssey 2EQ, Press [ENTER].

Get Onkyo HT-SP904 PDF manuals and user guides View all Onkyo HT-SP904 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

First Time Setup-Continued Using Audyssey 2EQ 1 STANDBY/ON STANDBY TUNING PRESET MASTER VOLUME PHONES MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER C D SETUP ENTER RETURN DISPLAY DIGITAL INPUT TONE STEREO LISTENING MODE DIMMER MEMORY TUNING MODE CLEAR SETUP MIC AUX INPUT VIDEO L AUDIO R Notes: • If the AV receiver was previously muted, it will be unmuted. • Automatic speaker setup cannot be performed while a pair of headphones is connected. • It takes about 10 minutes to complete the automatic speaker setup. 2, 6 SETUP MIC 1 Turn on the AV receiver. 2 Put the speaker setup microphone at measurement point 1 (page 37), and connect it to the SETUP MIC jack. SETUP MIC Notes: • Make sure the microphone is horizontal. • If there's an obstacle between the micro- phone and any speaker, the automatic setup will not work correctly. Set up the room as you would when enjoying a DVD. • Positioning the microphone close to where your ears would normally be will provide better results. You can adjust the height of the microphone by using a tripod or level table. 3 Press [ENTER]. The automatic speaker setup starts. A test tone is output by each speaker in turn, as the Audyssey 2EQ function determines which speakers are connected. This takes a few minutes. Note: • If any extraneous noise is picked up by the microphone, the automatic setup may not work correctly, so don't make any noise. 4 When the following display appears, move the speaker setup microphone to measurement point 2 (page 37), and then press [ENTER]. Audyssey 2EQ performs more measurements. This takes a few minutes. 5 When the following display appears, move the speaker setup microphone to measurement point 3 (page 37), and then press [ENTER]. Audyssey 2EQ performs more measurements. This takes a few minutes. When the measurements are complete, the results are calculated and saved automatically. 6 When the automatic speaker setup is complete, disconnect the speaker setup microphone. Notes: • When the automatic speaker setup is complete, the Equalizer Settings (page 61) will be set to "Audyssey." • You can cancel the automatic speaker setup at any point in this procedure simply by disconnecting the setup microphone. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
38
First Time Setup
—Continued
Using Audyssey 2EQ
Notes:
•
When the automatic speaker setup is complete, the
Equalizer Settings (page 61) will be set to “Audyssey.”
•
You can cancel the automatic speaker setup at any
point in this procedure simply by disconnecting the
setup microphone.
1
Turn on the AV receiver.
2
Put the speaker setup microphone at
measurement point
1
(page 37), and
connect it to the SETUP MIC jack.
Notes:
•
Make sure the microphone is horizontal.
•
If there’s an obstacle between the micro-
phone and any speaker, the automatic setup
will not work correctly. Set up the room as
you would when enjoying a DVD.
•
Positioning the microphone close to where
your ears would normally be will provide
better results. You can adjust the height of the
microphone by using a tripod or level table.
3
Press [ENTER].
The automatic speaker setup starts.
A test tone is output by each speaker in turn, as
the Audyssey 2EQ function determines which
speakers are connected. This takes a few min-
utes.
Note:
•
If any extraneous noise is picked up by the
microphone, the automatic setup may not
work correctly, so don’t make any noise.
MASTER VOLUME
VIDEO
STANDBY
TONE
DISPLAY
STEREO
DIMMER
MEMORY
DIGITAL INPUT
TUNING MODE
TUNER
TAPE
AUX
CBL/SAT
VCR/DVR
DVD
MULTI CH
C
D
SETUP
ENTER
SETUP MIC
RETURN
LISTENING MODE
AUDIO
L
R
AUX INPUT
STANDBY/ON
PHONES
TUNING
PRESET
SETUP MIC
1
2, 6
SETUP MIC
4
When the following display appears,
move the speaker setup microphone to
measurement point
2
(page 37), and
then press [ENTER].
Audyssey 2EQ performs more measurements.
This takes a few minutes.
5
When the following display appears,
move the speaker setup microphone to
measurement point
3
(page 37), and
then press [ENTER].
Audyssey 2EQ performs more measurements.
This takes a few minutes.
When the measurements are complete, the
results are calculated and saved automatically.
6
When the automatic speaker setup is
complete, disconnect the speaker setup
microphone.
Notes:
•
If the AV receiver was previously muted, it will
be unmuted.
•
Automatic speaker setup cannot be performed
while a pair of headphones is connected.
•
It takes about 10 minutes to complete the auto-
matic speaker setup.