Onkyo TX-DS898 Owner Manual - Page 41

Audio Adjust 3-4. Delay This sub-menu gives you various ways to adjust the timing of the audio output from the speakers to give certain soundfield effects or to adjust for unwanted asynchronous video and audio tracks. This sub-menu does not appear if "Direct" is selected as the listening mode. a A/V Sync Relative Delay b Center c Surr L/R d Surr Back Parameter 0.0 ms to 74.0 ms -4.0 ms to +6.0 ms -4.0 ms to +6.0 ms -4.0 ms to +6.0 ms Setting Initial value 0.0 ms 0.0 ms 0.0 ms 0.0 ms a. A/V Sync If a digital signal processor is connected, there may be times when the audio and video from a DVD or LD player is not output in perfect sync. The result is where the sound and picture do not match and the sound is heard too early. In such a case, use this setting to properly synchronize the audio and video. This setting can be set between 0 to 74.0 ms in 0.5-ms increments. Under normal circumstances, this can left at 0 ms. If set between 25.0 and 74.0 ms, upsampling is fixed to 24.0 ms. For input sources using the multi channel port, this setting will not appear. Relative Delay b. Center, c. Surr L/R, d. Surr Back Besides level and delay adjustments, the TX-DS898 provides the ability to change or adjust the relative speaker position to fine tune the soundfield for the listener. This is accomplished using Onkyo's unique Enhanced Spatial Positioning Algorithm. This adjustment provides 10 milliseconds of delay for the speakers, which is equivalent to moving the speaker 10 feet away. This adjustment is set up to provide -4.0 or +6.0 milliseconds (-4 or +6 feet) of adjustment to the listener's position. Once the coarse adjustments--speaker level and distance adjustments--are made, the system is set up to provide a typical or broad surround environment. By adjusting the relative position of the speakers, we are able to alter the soundfield to be more spread out (deeper) or focused (shallower). Note: Surr Back will not appear if the Powered Zone 2 setting of the Speaker Config sub-menu is set to "Activated." 3-5. LFE Level Setup This sub-menu is for setting the LFE (Low Frequency Effect) levels included in Dolby Digital and DTS software. Parameter Setting Initial value a Dollby Digital -∞, -10 dB to 0 dB 0 dB b DTS -∞, -10 dB to 0 dB 0 dB a. Dolby Digital The level can be adjusted to either -∞ or between -10 to 0 decibels in 1-decibel increments. For Dolby Digital input source signals, the LFE level becomes that set here. A setting of 0 decibels is recommended for optimum performance; however, if the low frequency range is too strong, lower this setting as necessary. b. DTS The level can be adjusted to either -∞ or between -10 to 0 decibels in 1-decibel increments. For DTS input source signals, the LFE level becomes that set here. A setting of 0 decibels is recommended for optimum performance; however, if the low frequency range is too strong, lower this setting as necessary. 3-6. Mono Setup The settings shown below are enabled when the listening mode is set to "Mono." Parameter Setting Initial value a Academy On, Off Off b Input Channel Auto L+R, Left, Right Auto L+R a) Academy Older monaural film mixes relied on high-frequency rolloff in presentation to sound properly balanced, so that excessive hiss from the grain structure of the film would not be heard. The highfrequency loss was typically due to a combination of optical slit loss, electrical filters, loudspeaker response, and screen loss. Some films have been transferred to video without such a high-frequency rolloff, and thus sound overly bright and hissy. This unit includes this "Academy filter," which is based on contemporary playback practices for such films over wide-range systems. This can be set to either "On" or "Off." b) Input Channel This allows you to set which input channel to use for monaural sound. Auto L+R: Select this under normal circumstances. When the input source is center channel only, this channel is used for monaural sound input channel. Otherwise, left and right channels are mixed and the mixed signal is used for monaural sound input channel. Left/Right: You will need to select either left or right when playing a video source that contains bilingual data. In such a case, the left and right channels will contain different language. Select the channel with the language you desire. 3-7. Theater Dimensional Setup Select this to modify the Theater-Dimensional (T-D) listening modes. The parameters that can be set are shown in the table below. Parameter Setting Initial value a Listening Angle 20 deg, 40 deg 20 deg b Center On, Off Off c Front Expander On, Off On d Virtual Surr Level -3 dB to +3 dB 0 dB e Dialog Enhance On, Off Off Theater Dimensional For the best enjoyment of your home theater, it is recommended that you have at least front left and right speakers, a center speaker, and surround left and right speakers. However, if you only have front left and right speakers, you can enjoy multichannel audio by using this mode. This mode controls the characteristics of the sound that reaches each ear to reproduce a multi-speaker setup. To receive the full effect, there is an optimum listening position (sweet spot). Refer to the explanation of the listening angle. In addition, if the reflective sound components are large, it may be difficult to achieve the desired result, so be sure to set up your system and listening position to minimize reflective sound. 41