Onkyo TX-DS898 Owner Manual - Page 71

Troubleshooting guide VIDEO and AUDIO Desired picture does not appear. • Improper connection. © Check the connection again. Insert the plugs and connectors completely. No OSD Menu display. • Improper connection. © Check connections. • OSD Menu is displayed when monitor is connected to VIDEO or S VIDEO of MONITOR OUT. © Confirm connections (see page 18). No sound, or sound of the selected source is not heard. • Input Setup menu settings are incorrect. © Check settings (see page 33). No picture appears on the TV screen (or monitor). • TV (or monitor) is not set to receive the output signals from the receiver. © Set the TV (or monitor) to the receiver input. • Video cable is not connected securely. © Check connections. • You have connected to the COMPONENT VIDEO connectors but the TX-DS898 is not set properly. © Check the Video Setup submenu of the Input Setup menu (page 35). REMOTE CONTROLLER Front panel controls function but remote controller controls do not. • No batteries in remote controller. © Insert batteries. • Batteries have worn out. © Replace batteries. • Remote controller is not pointed at the remote sensor of the TX- DS898. © Point the remote controller at the remote sensor of the TX- DS898. • Remote controller is too far from the TX-DS898. © Operate the remote controller within 5 meters (16 feet). • Remote controller is functioning in a different mode © Press the RCVR MODE button. OTHER LATE NIGHT function cannot be used. • Playback source is not Dolby Digital encoded. © Check that the DOLBY DIGITAL indicator lights up on the display. Re-EQ function cannot be used. • Listening mode is set to Theater-Dimensional, THX, or Direct/ Pure Audio. © See page 43. Parameter cannot be set for Front Effect etc. • Parameter may not be able to be set depending on the listening mode. © See table on page 43. Multichannel audio is not output. • To listen to multichannel audio, "Yes" must be selected in the "Multichannel" in the Multichannel setup sub-menu of the Input Setup menu. Also, it is necessary to select Multichannel with the AUDIO SELECTOR button. © Check that the component is connected to the MULTI CHANNEL INPUT port and check the Setup menu settings. Components in remote zone (Zone 2) do not operate properly. • Components are incorrectly connected. © Check connections. • Objects are interfering with remote controller signals. © Move inferring objects away from path of remote controller signals. If one of the messages shown below appears "Not available with headphones use" The operation is not allowed because headphones are plugged into the TX-DS898. "Not available with Multichannel use" Cannot be used while the multi-channel output is being used. "Not available in this Sp Config" Will not work with the current speaker configuration settings. "Not available in Zone 2 mode" The operation is not allowed because the Zone 2 mode is turned on. "Only available with Dolby D" No setting other than Dolby Digital can be set. "Not available in this Listening mode" Will not work with the current listening mode. "Not available with this signal" The listening mode cannot be selected with the current input source. "Powerd Zone 2 is not Activated" Will not work with the Zone 2 output set to non-activated (Not Activated). "Not available with Muting" Will not work because the muting is activated. "Zone 2 is not On" Will not work because the Zone 2 has not been turned on. Also refer to the respective instruction manuals of the compact disc player, DVD player, video cassette recorder, TV monitor, etc., that compose your entertainment system. The TX-DS898 contains an internal microcomputer that performs high-level operations. However, on extremely rare occasions, noise or interference from an external source or static electricity may cause faulty operation. If this occurs, unplug the power cord from the wall outlet, wait five or more seconds, and then plug it back in. This should correct the situation. * To reset the surround mode and other settings to the factory default settings, hold down the VIDEO 1 button with the TXDS898 turned on and then press the STANDBY/ON button. "CLEAR" appears in the front display and the TX-DS898 enters the standby state. 71