Onkyo TX-NR1000 Owner Manual - Page 50

Connecting the Power/Basic Operations • Before you plug in the TX-NR1000/TX-NR5000E, confirm that all connections have been made properly. • Turning on the power may cause a momentary power surge, which might interfere with other electrical equipment on the same circuit, such as computers. If this happens, use a wall outlet on a different circuit. (All models other than USA, Canadian, and Australian models) The TX-NR1000/TX-NR5000E is shipped with the main power (POWER) switch in the on position ( ON ). When the power cord is plugged in for the first time, the TX-NR1000/TX-NR5000E will automatically enter the standby state and the [STANDBY] indicator will light (same condition after step 2 below on the left coloumn). STANDBY/ON Input source buttons STANDBY indicator MASTER VOLUME STANDBY/ON Input source buttons STANDBY indicator MASTER VOLUME STANDBY/ON MASTER VOLUME STANDBY REC / ZONE 3 ( RED ) MAIN ( BLUE ) ZONE 2 ( GREEN ) PURE AUDIO DISPLAY TAPE 1 TAPE 2 TUNER PHONO C D NET AUDIO DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7 OPEN PHONES LISTENING AUDIO MODE SELECTOR TONE TUNING MODE MEMORY DIMMER CLEAR ZONE 2 SELECT/ PRESET SETUP CONTROL / TUNING REC/ZONE 3 LEVEL PUSH TO ENTER EXIT PUSH TO ENTER LEVEL DIGITAL S VIDEO VIDEO 7 INPUT VIDEO L AUDIO R STANDBY/ON MASTER VOLUME STANDBY POWER ON OFF REC / ZONE 3 ( RED ) MAIN ( BLUE ) ZONE 2 ( GREEN ) PURE AUDIO DISPLAY TAPE 1 TAPE 2 TUNER PHONO C D NET AUDIO DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7 OPEN PHONES LISTENING AUDIO MODE SELECTOR TONE TUNING MODE MEMORY RT/PTY/TP CLEAR ZONE 2 SELECT/ PRESET SETUP CONTROL / TUNING REC/ZONE 3 LEVEL PUSH TO ENTER EXIT PUSH TO ENTER LEVEL DIGITAL S VIDEO VIDEO 7 INPUT VIDEO L AUDIO R To wall outlet (USA, Canadian, and Australian models) POWER (Other models) To wall outlet Turning on the Power 1 POWER ON OFF STANDBY 2 STANDBY/ON STANDBY Turn off Plug the power cord into an AC wall outlet. (USA, Canadian, and Australian models) The [STANDBY] indicator will light up. (Other models) Press the [POWER] switch to set the TX-NR1000/TX-NR5000E to standby state. The [STANDBY] indicator will light up. Press the [STANDBY/ON] button to turn on the TX-NR1000/ TX-NR5000E. The display will light up and the [STANDBY] indicator will turn off. If you press the [STANDBY/ON] button again, the TX-NR1000/TX-NR5000E returns to the standby state. Note: Any components connected via will also be turned on when the remote controller's [ON] button is pressed. Operating on the TX-NR1000/ TX-NR5000E 1 DISPLAY TUNER PHONO DVD VIDEO 1 Select an input source. Press the input source button. TAPE 1 TAPE 2 *You cannot listen to a source in main CD NETAUDIO room A, and to another source in main room B. VIDEO2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7 2 Start playing the device selected. When playing a picture device such as a DVD player, you need to switch input to a monitor such a TV set. Some picture-playing devices such as a DVD-type game machine may also require setting of sound output. Refer to the manual of the device connected. 3 Adjust the volume level with the [MASTER VOLUME] dial. MASTER VOLUME You can adjust the volume level in the range from -∞, -81.5 dB to 18.0 dB (Max) (when Relative is selected in the Volume Setup sub-menu). Hint: TX-NR1000/TX-NR5000E is a product for users to enjoy home theater, so it is equipped with a wide range of volume levels. Please fine tune the volume level aaccording to your preferences. 50