Onkyo TX-NR555 User Manual - Page 58
If an Error Message is Displayed, Updating via USB, Update, Error Code, Preparation
View all Onkyo TX-NR555 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 58 highlights
>>Specifications >>Settings >>Listening Modes >>Playback Function >>Basic Manual Troubleshooting | Appendix Setup 1. Input/Output Assign 2. Speaker 3. Audio Adjust 4. Source 5. Hardware 6. Multi Zone 7. Miscellaneous 1. Tuner 2. Remote ID 3. Firmware Update 4. Initial Setup 5. Lock • If "Firmware Update" is grayed out and cannot be selected, wait for a while until it starts up. • You will not be able to select "Update via NET" if there is nothing to update. 3. Press ENTER with "Update" selected to start update. • During the update, the TV screen may go black depending on the updated program. In that case, check the progress on the display of the unit. The TV screen will remain black until the update is complete and the power is turned on again. • "Completed!" is displayed when the update is complete. 4. Press ON/STANDBY on the main unit to turn the unit into standby mode. The process is completed and your firmware is updated to the latest version. • Do not use on the remote controller. Error Code • ˎ-01, ˎ-10ɿ Ethernet cable not found. Connect the Ethernet cable properly. • ˎ-02, ˎ-03, ˎ-04, ˎ-05, ˎ-06, ˎ-11, ˎ-13, ˎ-14, ˎ -16, ˎ-17, ˎ-18, ˎ-20, ˎ-21ɿ Internet connection error. Check the following: - The router is turned on - This unit and the router are connected via the network Try to disconnect and then connect again the power to the unit and router. This may solve the problem. If you are still unable to connect to the Internet, the DNS server or proxy server may be temporarily down. Check the service status with your ISP provider. • Others Disconnect then reconnect the AC power cord, then repeat from the beginning. Updating via USB Preparation: • Prepare a 128MB or larger USB storage device. FAT16 or FAT32 file system format. - Media inserted in a USB card reader may not be used for this function. - USB storage devices with security function are not supported. - USB hubs and USB devices with hub function are not supported. Do not connect these devices to the unit. • Delete any data stored on the USB storage device. • Turn off the controller component (PC etc.) connected to the network. • Stop any playing Internet radio, USB storage device, or server content. • If the multi-zone function is active, turn it off. • If "HDMI CEC" is set to "On", set it to "Off". - Press on the remote controller. Then, after selecting "5. Hardware" - "HDMI" and pressing ENTER, select "HDMI CEC" and select "Off". * Some USB storage devices may take long to load, may not be loaded correctly, or may not be correctly fed depending on the device or their content. * Our company will not be liable whatsoever for any loss or damage of data, or storage failure arising from the use of the USB storage device with this unit. Thank you for your understanding. * The description may differ from the on-screen display but that will not change the way to operate or the function. ˙ If an Error Message is Displayed When an error occurs Error!" is displayed on the display of the unit. ("*" represents an alphanumeric character.) Check the following: 26 ˙ Update 1. Connect the USB storage device to your PC. 2. Download the firmware file from our company's website to your PC and unzip. Firmware files are named in the following way: ONKAVR zip Unzip the file on your PC. The number of unzipped files and folders varies depending on the model. 3. Copy all unzipped files and folders to the root folder of the USB storage device. • Make sure to copy the unzipped files.