Onkyo TX-NR801 Owner Manual - Page 72

Enjoying Net Audio-Continued DIRECT/PURE AUDIO STEREO SURROUND THX DSP TUNING SETUP ENTER PRESET RE TURN MEMORY FM MODE A-FORM LISTENING MODE MEMORY // / SETUP ENTER // / ENTER SETUP Network Setup Menu Before you can use the TX-NR801/TX-NR801E to play music contained in the music library on the Net-Tune server and listen to Internet radio, you must correctly configure the TX-NR801/TX-NR801E's network settings so that it can connect to your LAN and the Internet. It is strongly recommended to use a broadband connection (via an xDSL or CATV leased line) and a router. If you are connected to the Internet via a narrowband dialup connection, you may not be able to enjoy Internet radio as you expect or at all. Before setting up the TX-NR801/TX-NR801E, make sure that you are already using a router that provides Internet access and that the TX-NR801/TX-NR801E is correctly connected with your router or hub via a LAN cable. For more information on Internet connectivity, consult with your ISP (Internet Service Provider) or refer to the router documentation. DHCP (Dynamic Host Configuration Protocol) and AutoIP are mechanisms for network configuration, which assign IP addresses automatically to network devices such as the TX-NR801/TX-NR801E, PC, and broadband router. DNS (Domain Name System) is a mechanism which translates domain names into IP addresses or vice versa. Domain names such as www.onkyo.co.jp are used for Web browsing, and IP addresses such as 210.199.170.69 are used for actual network data transfer. Advanced Menu 0.Hardware Setup 1.Speaker Setup 2.Input Setup 3.Audio Adjust 4.Preference 5.Network Setup →Basic Menu 5.Network Setup 1.IP Address 2.Proxy Setup 3.MAC Address 4.Client Setup →Save Settings [ENTER]Quit:[SETUP] [ENTER]Quit:[SETUP] If you want to perform these operations using the remote controller, first press the RCVR button. 1 Display the main menu. Press the SETUP button on the front panel or SETUP button on the remote controller to display the main menu on the monitor and front display. When the "Basic Menu" is displayed, select "→Advanced Menu" using the and cursor buttons and press the ENTER button to display the "Advanced Menu." 2 Use the and cursor buttons to select "5. Network Setup" and then press the ENTER button. The "Network Setup" menu appears. 3 Use the and cursor buttons to select an item and then press the ENTER button. 4 Use the and cursor buttons to select an item and then use the and cursor buttons to set the desired value. 5 Press the SETUP button to exit the Setup menu. Press the RETURN button to return to the previous menu. IP Address Sub-menu You can use this submenu to turn on/off the DHCP and Auto IP functionality. Also, you can use this menu to manually configure network settings. Referring to the documentation from your ISP, enter the IP address and subnet mask assigned to your TX-NR801/TX-NR801E as well as the IP addresses of the default gateway and DNS server. After the necessary settings are complete, press the RETURN button to go back to "5. Network Setup Menu," select "→ Save Settings, " and press the ENTER button to save the setting you made. When you set a. DHCP/AUTO IP to Off, select a menu item under b. and press the ENTER or button; the TX-NR801/TX-NR801E will enter the number-entry mode. Select a number using the / buttons, and press the ENTER button to enter the number. After all the necessary numbers are entered, the TX-NR801/TX-NR801E exits the number-entry mode. 5-1.IP Address a.DHCP/AUTO-IP :On b.IP Address :192.168. 9. 10 c.SUBNET Mask :255.255.255. 0 d.Gateway :192.168. 9. 1 DNS Server e.1st:192.168. 9. 1 f.2nd: 0. 0. 0. 0 72