Onkyo TX-SR701 Owner Manual - Page 43

Temporarily changing the speaker output levels, To change the display of the input source from, TAPE

Get Onkyo TX-SR701 - THX Select Digital A/V Receiver PDF manuals and user guides
UPC - 751398005183
View all Onkyo TX-SR701 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Selecting an Audio Component Temporarily changing the speaker output levels To change the individual speaker volumes temporarily, follow the procedure given below. Each channel can be set between -12 and +12 decibels. For subwoofer, values between -15 and +12 decibels can be set. Note that the calibration settings will return to the original settings when the TX-SR701/701E/601/601E is put in standby. Using the remote controller: 1. Press the RCVR MODE button. 2. Press the CH SEL button and select the desired speaker. 3. Press the LEVEL or button to adjust the volume level. Notes: • You cannot select a speaker if the configuration value of the speaker is set to "No" or "None." • If the speaker level is set to +1 dB or higher, the maximum level indicated on the display will change if you raise the volume level. • When you press the TEST button after you set the level, the current level will be used as the value set via the test tone. To change the display of the input source from TAPE to MD If you connected an MD recorder to the TAPE jacks of the TXSR701/701E/601/601E, you can have "MD" appear when the TAPE source button is pressed. By changing the display, when an Onkyo MD recorder is -connected, the system functions will become enabled. Changing the display: Press and hold down the TAPE source button until the display changes from TAPE to MD (approx. 3 seconds). TAPE To return the display to its original setting, perform the same procedure. This setting is necessary to allow system functions for a connected Onkyo cassette tape or MD recorder. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
43
Selecting an Audio Component
To change the individual speaker volumes temporarily, follow the
procedure given below. Each channel can be set between –12 and
+12 decibels. For subwoofer, values between –15 and +12 decibels
can be set. Note that the calibration settings will return to the
original settings when the TX-SR701/701E/601/601E is put in
standby.
Using the remote controller:
1.
Press the RCVR MODE button.
2.
Press the CH SEL button and select
the desired speaker.
3.
Press the LEVEL
or
button to
adjust the volume level.
Notes:
•
You cannot select a speaker if the configuration value of the
speaker is set to “No” or “None.”
•
If the speaker level is set to +1 dB or higher, the maximum level
indicated on the display will change if you raise the volume
level.
•
When you press the TEST button after you set the level, the
current level will be used as the value set via the test tone.
If you connected an MD recorder to the TAPE jacks of the TX-
SR701/701E/601/601E, you can have “MD” appear when the TAPE
source button is pressed. By changing the display, when an Onkyo
MD recorder is
-connected, the
system functions will
become enabled.
Changing the display:
Press and hold down the TAPE source button until the display
changes from TAPE to MD (approx. 3 seconds).
To return the display to its original setting, perform the same
procedure. This setting is necessary to allow
system functions
for a connected Onkyo cassette tape or MD recorder.
Temporarily changing the speaker output levels
To change the display of the input source from
TAPE to MD
TAPE