Optoma HD50 User's Manual - Page 5

Precautions, English - lamp

Get Optoma HD50 PDF manuals and user guides View all Optoma HD50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

English Usage Notice Precautions Please follow all warnings, precautions and maintenance as recommended in this user's guide. ▀■ Warning- ▀■ Warning▀■ Warning▀■ Warning- ▀■ Warning- Noottee ▀■ Warning- When the lamp reaches the end ▀■ Warningof its life, the projector will not turn back on until the lamp module has been replaced. ▀■ Warning- To replace the lamp, follow the procedures listed ▀■ Warning- under "Replacing the Lamp" section on page 56. Do not look into the projector's lens when the lamp is on. The bright light may hurt your eyes. To reduce the risk of fire or electric shock, do not expose this projector to rain or moisture. Please do not open or disassemble the projector as this may cause electric shock. When replacing the lamp, please allow the unit to cool down. Follow instructions as described on page 56. This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages. Reset the "Lamp Reset" function from the on-screen display "System|Lamp Setting" menu after replacing the lamp module (refer to pages 42-43). When switching the projector off, please ensure the cooling cycle has been completed before disconnecting power. Allow 90 seconds for the projector to cool down. Do not use lens cap when projector is in operation. When the lamp is approaching to the end of its life time, the message "Replacement suggested" will show on the screen. Please contact your local reseller or service center to change the lamp as soon as possible. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
English
5
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
▀
■
Warning-
Do not look into the projector's lens when
the lamp is on. The bright light may hurt your
eyes.
▀
■
Warning-
To reduce the risk of fire or electric shock, do
not expose this projector to rain or moisture.
▀
■
Warning-
Please do not open or disassemble the
projector as this may cause electric shock.
▀
■
Warning-
When replacing the lamp, please allow the
unit to cool down. Follow instructions as de-
scribed on page 56.
▀
■
Warning-
This projector will detect the life of the lamp
itself. Please be sure to change the lamp
when it shows warning messages.
▀
■
Warning-
Reset the "Lamp Reset" function from the
on-screen display "System|Lamp Setting"
menu after replacing the lamp module
(refer to pages 42-43).
▀
■
Warning-
When switching the projector off, please
ensure the cooling cycle has been completed
before disconnecting power. Allow 90 sec-
onds for the projector to cool down.
▀
■
Warning-
Do not use lens cap when projector is in
operation.
▀
■
Warning-
When the lamp is approaching to the end of
its life time, the message "Replacement sug-
gested" will show on the screen.
Please contact your local reseller or service
center to change the lamp as soon as pos-
sible.
N
ote
N
ote
When the lamp
reaches the end
of its life, the
projector will not
turn back on until
the lamp module
has been replaced.
To replace the
lamp, follow the
procedures listed
under "Replacing
the Lamp" section
on page 56.