Optoma HD50 User's Manual - Page 53

Other, Image is too small or too large

Get Optoma HD50 PDF manuals and user guides View all Optoma HD50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

English Appendices Image is too small or too large  Adjust the zoom lever from the lens.  Move the projector closer to or further from the screen.  Press [Menu] on the projector panel, go to "Display -> Format". Try the different settings. Image has slanted sides:  If possible, reposition the projector so that it is centered on the screen and below the bottom of the screen and use PureShift to make adjustments to the image position.  Use "Display->V Keystone" from the OSD to make an adjustment. Image is reversed  Select "System -> Projection" from the OSD and adjust the projection direction. Other The projector stops responding to all controls  If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. Lamp burns out or makes a popping sound  When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on page 56. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
English
53
Appendices
Image is too small or too large
Adjust the zoom lever from the lens.
Move the projector closer to or further from the screen.
Press [Menu] on the projector panel, go to “Display ->
Format”. Try the different settings.
Image has slanted sides:
If possible, reposition the projector so that it is centered
on the screen and below the bottom of the screen and use
PureShift to make adjustments to the image position.
Use “Display->V Keystone” from the OSD to make an ad-
justment.
Image is reversed
Select “System -> Projection” from the OSD and adjust the
projection direction.
Other
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power
cord and wait at least 20 seconds before reconnecting
power.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and
may make a loud popping sound. If this happens, the
projector will not turn on until the lamp module has been
replaced. To replace the lamp, follow the procedures in the
“Replacing the Lamp” section on page 56.