Optoma TW865-NLW User Manual - Page 15

Powering off the projector

Get Optoma TW865-NLW PDF manuals and user guides View all Optoma TW865-NLW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Installation Powering Off the Projector . Press the "Standby" button on the remote control or "Off" on the control panel to turn off the projector.  The following message will be displayed on the screen. Press the " Standby " button on the remote control or "Off" on the control panel again  to confirm otherwise the message will disappear after 5 seconds. When you pressing for the second time, the projector will shut down. 2. The cooling fans continue to operate for about 60 seconds for cooling cycle and the POWER LED will flash Blue. When the POWER LED turns red, the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press the " " button either on the rear of the projector or on the remote control to restart the projector. 2 3. Power off the switch. 3 4. Disconnect the power cord from the electrical outlet and from the projector. 5. Do not turn on the projector immediately following the power off procedure. 1 3 2 5 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
English
±5
Installation
Powering Off the Projector
±. Press the
“
Standby
”
button on the remote control or “Off” on the
control panel to turn off the projector.
±
The following message will be displayed on the screen.
Press the
“
Standby
”
button on the remote control or “Off” on the
control panel again
±
to confirm otherwise the message will disap-
pear after ±5 seconds. When you pressing for the second time,
the projector will shut down.
2. The cooling fans continue to operate for about 60 seconds for
cooling cycle and the POWER LED will flash Blue. When the
POWER LED turns red, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until
the projector has completed the cooling cycle and has entered
standby mode. Once in standby mode, simply press the
“
”
but-
ton either on the rear of the projector or on the remote control to
restart the projector.
2
3. Power off the switch.
3
4. Disconnect the power cord from the electrical outlet and from the
projector.
5. Do not turn on the projector immediately following the power off
procedure.
1
3
2