Optoma TW865-NLW User Manual - Page 79

Lamp Replacing Procedure, To replace the lamp module, reverse the previous steps.

Get Optoma TW865-NLW PDF manuals and user guides View all Optoma TW865-NLW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

NOTE  The screws on the lamp door and the lamp are not detachable.  The projector cannot be turned on if the lamp cover is open.  Do not touch the glass area of the lamp. Hand oil can cause the lamp to shatter. Use a dry cloth to clean the lamp module if it was accidentally touched. Appendices 1 2 3 4 Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the " " button. 2. Allow the projector to cool down for at least 30 minutes. 3. Disconnect the power cord. 4. Unscrew the two screws on the lamp door. 1 5. Open and pull up the lamp door. 2 6. Unscrew the three screws on the lamp housing. 3 7. Pull out the lamp module slowly and carefully. 4 To replace the lamp module, reverse the previous steps. 8. Turn on the projector and use "Lamp Reset" after the lamp module is replaced. Lamp Reset: (i) Press "Menu"  (ii) Select "OPTIONS"  (iii) Select "Lamp Settings"  (iv) Select "Lamp Reset"  (v) Select "Yes". 79 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
English
79
Appendices
Lamp Replacing Procedure:
±.
Switch off the power to the projector by pressing the “
” button.
2.
Allow the projector to cool down for at least 30 minutes.
3.
Disconnect the power cord.
4.
Unscrew the two screws on the lamp door.
±
5.
Open and pull up the lamp door.
2
6.
Unscrew the three screws on the lamp housing.
3
7.
Pull out the lamp module slowly and carefully.
4
To replace the lamp module, reverse the previous steps.
8.
Turn on the projector and use “Lamp Reset” after the lamp module
is replaced.
Lamp Reset: (i) Press “Menu”
(ii) Select “OPTIONS”
(iii) Select
“Lamp Settings”
(iv) Select “Lamp Reset”
(v) Select “Yes”.
2
4
N
OTE
The screws on
the lamp door
and the lamp are
not detachable.
The projector
cannot be turned
on if the lamp
cover is open.
Do not touch the
glass area of the
lamp. Hand oil
can cause the
lamp to shatter.
Use a dry cloth
to clean the
lamp module if it
was accidentally
touched.
1
3