Optoma W501 User's Manual - Page 71

EN-71, OPTIONS &gt, Lamp Settings

Page 71 highlights

1. Turn off the projector. 2. Unplug the power cord. 3. Open the top cover, by sliding the top cover forward, and lifting the top cover off.1 4. Remove the screw on the lamp cover and then open it up. 2 & 3 5. Loosen the screws from the lamp module. 4 6. Raise the handle and pull out the lamp module slowly and carefully. 5 7. Insert the new lamp module into the projector and tighten the screws. 8. Replace the lamp cover and tighten the screw. 9. Replace the top cover by (a) aligning the cover (b) sliding it toward the back and (c) locking it back into place. 10. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp. 11. Reset the lamp hour. Refer to the "OPTIONS > Lamp Settings" menu. Note „ Dispose the used lamp according to local regulations. „ Ensure that screws are tightened properly. Screws not tightened fully may result in injury or accidents. „ Since the lamp is made of glass, do not drop the unit and do not scratch the glass. „ Do not reuse the old lamp. This could cause the lamp to explode. „ Be sure to turn off the projector and unplug the AC power cord before replacing the lamp. „ Do not use the projector with the lamp cover removed. EN-71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93

EN-71
1.
Turn off the projector.
2.
Unplug the power cord.
3.
Open the top cover, by sliding the top cover forward, and lifting the top
cover off.1
4.
Remove the screw on the lamp cover and then open it up. 2 & 3
5.
Loosen the screws from the lamp module. 4
6.
Raise the handle and pull out the lamp module slowly and carefully. 5
7.
Insert the new lamp module into the projector and tighten the screws.
8.
Replace the lamp cover and tighten the screw.
9.
Replace the top cover by (a) aligning the cover (b) sliding it toward the
back and (c) locking it back into place.
10.
Turn on the projector.
If the lamp does not turn on after the warm-up
period, try reinstalling the lamp.
11.
Reset the lamp hour. Refer to the “
OPTIONS >
Lamp Settings
” menu.
Note
Dispose the used lamp according to local regulations.
Ensure that screws are tightened properly. Screws not tightened fully may result in
injury or accidents.
Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
Do not reuse the old lamp. This could cause the lamp to explode.
Be sure to turn off the projector and unplug the AC power cord before replacing the
lamp.
Do not use the projector with the lamp cover removed.