Optoma X343 S343 User Manual - Page 43

Each display mode can be adjusted and saved the value., In 3D timing mode

Get Optoma X343 PDF manuals and user guides View all Optoma X343 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

USING THE PROJECTOR Main Menu Sub Menu Regulatory Serial Number Source Resolution Refresh Rate Display Mode Power mode (Standby) Lamp Hours Information Network Status IP Address Projector ID Filter Usage Hours Brightness Mode FW Version Sub Menu 2 Bright Eco. Dynamic Eco+ Total System LAN MCU Sub Menu 3 Sub Menu 4 Values 00x00 0.00Hz 0 hr 0 hr 0 hr 0 hr 00~99 Note: ‡‡ The "Lamp Reset" in OSD will only reset both Lamp Hours in OSD and Lamp Hours in service mode. The Projection Hours in service mode will not be reset. Each display mode can be adjusted and saved the value. In 3D timing mode, the zoom/edge mask will be disabled to prevent from image break. The available menu options vary depending on the model type. English 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
English
43
USING THE PROJECTOR
Main
Menu
Sub Menu
Sub Menu 2
Sub Menu 3
Sub Menu 4
Values
Information
Regulatory
Serial Number
Source
Resolution
00x00
Refresh Rate
0.00Hz
Display Mode
Power mode
(Standby)
Lamp Hours
Bright
0 hr
Eco.
0 hr
Dynamic
0 hr
Eco+
0 hr
Total
Network Status
IP Address
Projector ID
00~99
Filter Usage
Hours
Brightness
Mode
FW Version
System
LAN
MCU
N±oe°
±
The “Lamp Reset” in OSD will only reset both Lamp Hours in OSD and Lamp Hours in service mode.
The Projection Hours in service mode will not be reset.
±
Each display mode can be adjusted and saved the value.
±
In 3D timing mode, the zoom/edge mask will be disabled to prevent from image break.
±
The available menu options vary depending on the model type.