Optoma ZU850 ZU850 User Manual - Page 42

Serial Port Path, Network Factory Reset

Get Optoma ZU850 PDF manuals and user guides View all Optoma ZU850 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

USING THE PROJECTOR Communications menu DISPLAY OUTPUT SETUP Communications LAN WLAN Network Serial Port Baud Rate Serial Port Path Projector Address 19200 RS232 0 OPTION LAN Configure the local area network (LAN) settings. ‡‡ DHCP: Turn the DHCP ON/OFF. ‡‡ IP Address: Select an IP address. ‡‡ Subnet Mask: Select subnet mask number. ‡‡ Gateway: Select the default gateway of the network connected to the projector. ‡‡ MAC Address: Display the network MAC Address value. ‡‡ WLAN Apply: Apply Network settings. Configure the wireless local area network (WLAN) settings. ‡‡ Enable: Enable/Disable WLAN. ‡‡ Start IP: Start of IP Address. ‡‡ End IP: End of IP Address. ‡‡ Subnet Mask: Assign Network Subnet Mask. ‡‡ Gateway: Assign Network Default Gateway. ‡‡ MAC Address: Display network MAC Address value. ‡‡ SSID: Assign Network Service Set Identifier. Network Configure the general network settings. ‡‡ Projector Name: Display the projector hostname for Network. ‡‡ Restart Network: Restart the network. ‡‡ Network Factory Reset: Perform factory reset on the network settings. The Projector Name, LAN IP, WLAN IP, and SNMP settings will be reset Serial Port Baud Rate Select the serial port its baud rate. Serial Port Path Select the serial port path from either RS232 or HDBaseT. Projector Address Set the projector address. The projector will respond to IR remotes set either at the same address as the projector or to IR remotes set to address 0. 42 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
English
42
USING THE PROJECTOR
Communications menu
DISPLAY
OUTPUT
SETUP
OPTION
Communications
19200
RS232
0
LAN
WLAN
Network
Serial Port Baud Rate
Serial Port Path
Projector Address
LAN
Configure the local area network (LAN) settings.
±
DHCP
: Turn the DHCP ON/OFF.
±
IP Address
: Select an IP address.
±
Subnet Mask
: Select subnet mask number.
±
Gateway
: Select the default gateway of the network connected to the projector.
±
MAC Address
: Display the network MAC Address value.
±
Apply
: Apply Network settings.
WLAN
Configure the wireless local area network (WLAN) settings.
±
Enable
: Enable/Disable WLAN.
±
Start IP
: Start of IP Address.
±
End IP
: End of IP Address.
±
Subnet Mask
: Assign Network Subnet Mask.
±
Gateway
: Assign Network Default Gateway.
±
MAC Address
: Display network MAC Address value.
±
SSID
: Assign Network Service Set Identifier.
Network
Configure the general network settings.
±
Projector Name
: Display the projector hostname for Network.
±
Restart Network
: Restart the network.
±
Network Factory Reset
: Perform factory reset on the network settings. The Projector Name, LAN IP,
WLAN IP, and SNMP settings will be reset
Serial Port Baud Rate
Select the serial port its baud rate.
Serial Port Path
Select the serial port path from either RS232 or HDBaseT.
Projector Address
Set the projector address. The projector will respond to IR remotes set either at the same address as the projector
or to IR remotes set to address 0.