Panasonic 52DL52 Operating Instructions - Page 18

Power

Get Panasonic 52DL52 - PT - 52inch CRT TV PDF manuals and user guides View all Panasonic 52DL52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Power ON / OFF I Connecting the Plug to the Wall Outlet The projection TV must first be switched on at the wall outlet. The projection TV will become standby mode. Turning the Power ON and OFF Always be sure to follow the procedure given below to turn the projection TV power ON and OFE • The lamp cooling fan will continue to operate for approximately 90 seconds after the power is turned off by the remote control. After the cooling fan has stopped, the power indicator will not illuminate (Stand-by). If you wish to turn the power ON while the cooling fan is operating, press the power button on the remote controller. The power indicator on the TV will then flash in green, and the projection "IV will turn ON as soon as the cooling fan stops. In normal circumstances, use the remote control to turn the power OFF (turning the picture OFF). Do not disconnect the power cord from the power outlet and do not open any circuit breakers while the cooling fan is still operating. Power switch Push the Power switch on the projection TV to turn the power on. pOWER oo o Push the Power switch on the projection TV to turn the set off. CH3 SAP JUST Remote control sensor VIVID Example: The screen above is displayed for a while after the projection TV is turned on. (Setting condition is an example.) 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Power
ON
/
OFF
Connecting
the Plug to the Wall Outlet
I
The projection
TV must first be switched
on at the wall
outlet.
The projection TV will become standby mode.
Turning
the Power ON and OFF
Always
be sure to follow the procedure given below to
turn
the projection
TV power ON and OFE
• The lamp cooling fan will continue to operate for approximately 90 seconds after the power is turned off by the remote control.
After the cooling fan has stopped, the power indicator will not illuminate
(Stand-by).
If you wish to turn the power ON while the cooling fan is operating,
press the power button on the remote controller. The
power indicator on the TV will then flash in green, and the projection "IV will turn ON as soon as the cooling fan stops.
In normal circumstances,
use the remote control to turn the power OFF (turning the picture OFF).
Do not disconnect
the power cord from the power outlet and do not open any circuit breakers while the cooling
fan is still operating.
Power switch
Push the Power switch on the projection TV to turn the power
on.
pOWER
oo
o
Remote control
sensor
Push the Power switch on the projection TV to turn the set off.
CH3
SAP
JUST
VIVID
Example: The screen above is displayed for a while after the
projection TV is turned on. (Setting condition is an
example.)
18