Panasonic AG-DVC7 Dv Camcorder - Page 11

THE REMOTE CONTROLLER, Inserting a Button-type Battery - press reset

Get Panasonic AG-DVC7 - Pro MiniDV Proline Camcorder PDF manuals and user guides
UPC - 791871302330
View all Panasonic AG-DVC7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

The Remote Controller Before Use $ Inserting a Button-type Battery Before using the Remote Controller, insert the supplied button-type battery. 1 While pressing the Stopper 1, pull out the Battery Holder. 1 2 Insert the button-type battery with the (+) marking facing upward. 3 Insert the Battery Holder into the Remote Controller. OWhen the button-type battery is exhausted, replace it with a new CR2025 battery. (A battery is normally expected to last about 1 year. However, it depends on operation frequency.) OMake sure to match the poles correctly when inserting the battery. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. WARNING Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 60°C or incinerate. Keep the Button-Type battery out of the reach of children. Never put Button-Type battery in mouth. If swallowed call your doctor. $ Using the Remote Controller 1 Direct the Remote Controller to the Remote Control Sensor 3 of the Camera Recorder and press an appropriate button. 3 15˚ 15˚ 15˚ 15˚ ODistance from the Camera Recorder: Within approximately 5 metres OAngle: Within approximately 15° in the vertical and horizontal directions from the central axis OThe above operative ranges are for indoor use. Outdoors or under strong light, the Camera Recorder may not operate properly even within the above ranges. OWithin a 1-metre range, you can also use the Remote Controller on the LCD Monitor side of the Camera Recorder. Selecting Remote Controller Modes When 2 Movie Cameras are used simultaneously, they can be operated individually by selecting different Remote Controller Modes. OIf the Remote Controller Mode of the Camera Recorder and that of the Remote Controller do not match, [REMOTE] Indication is displayed. Setup on the Camera Recorder: Set [REMOTE] on the [OTHER FUNCTIONS] SubMenu to the desired Remote Controller Mode. (-16-) Setup on the Remote Controller: 2 STILL ADV PAUSE STILL ADV INDEX STOP INDEX 1 SELECT [VCR1]: Press the [D] Button and [$] Button simultaneously. 1 [VCR2]: Press the [E] Button and [$] Button simultaneously. 2 OWhen the battery in the Remote Controller is replaced, the mode is automatically reset to [VCR1] Mode. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
11
B
e
f
o
r
e
U
s
e
The Remote Controller
$
Inserting a Button-type Battery
Before using the Remote Controller, insert the
supplied button-type battery.
1
1
While pressing the Stopper
1
, pull out the
Battery Holder.
$
Using the Remote Controller
15˚
15˚
15˚
15˚
3
STILL ADV
PAUSE
STILL ADV
INDEX
SELECT
STOP
INDEX
2
1
1
Direct the Remote Controller to the Remote
Control Sensor
3
of the Camera Recorder and
press an appropriate button.
O
Distance from the Camera Recorder:
Within approximately 5 metres
O
Angle:
Within approximately 15
°
in the vertical and
horizontal directions from the central axis
O
The above operative ranges are for indoor use.
Outdoors or under strong light, the Camera
Recorder may not operate properly even within the
above ranges.
O
Within a 1-metre range, you can also use the
Remote Controller on the LCD Monitor side of the
Camera Recorder.
Selecting Remote Controller Modes
When 2 Movie Cameras are used simultaneously,
they can be operated individually by selecting different
Remote Controller Modes.
O
If the Remote Controller Mode of the Camera
Recorder and that of the Remote Controller do not
match, [REMOTE] Indication is displayed.
Setup on the Camera Recorder:
Set [REMOTE] on the [OTHER FUNCTIONS] Sub-
Menu to the desired Remote Controller Mode. (
-16-
)
Setup on the Remote Controller:
[VCR1]:
Press the [
D
] Button and [
$
] Button
simultaneously.
1
[VCR2]:
Press the [
E
] Button and [
$
] Button
simultaneously.
2
O
When the battery in the Remote Controller is
replaced, the mode is automatically reset to [VCR1]
Mode.
2
Insert the button-type battery with the (+)
marking facing upward.
3
Insert the Battery Holder into the Remote
Controller.
O
When the button-type battery is exhausted,
replace it with a new CR2025 battery. (A battery
is normally expected to last about 1 year.
However, it depends on operation frequency.)
O
Make sure to match the poles correctly when
inserting the battery.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent
type recommended by the equipment
manufacturer. Discard used batteries according to
manufacturer
’
s instructions.
WARNING
Risk of fire, explosion and burns. Do not recharge,
disassemble, heat above 60
°
C or incinerate. Keep
the Button-Type battery out of the reach of children.
Never put Button-Type battery in mouth. If
swallowed call your doctor.