Panasonic CF-50GB2UUKM Operating Instructions - Page 3

Read Me First Getting Started For U.S.A. Federal Communications Commission Radio FCC Regulation Notice for modem Frequency Interference Statement This equipment contains a FCC approved modem. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Manufacturer of modem: AMBIT Microsystems Corporation FCC Rules. These limits are designed to provide reasonable Model No. T60M099.03 or J07M040.07 protection against harmful interference in a residential installation. This equipment generates, uses and can radiate Manufacturer of modem: PC TEL Inc. radio frequency energy and, if not installed and used in Model No. PCT2304WT accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television Tested To Comply With FCC Standards FOR HOME OR OFFICE USE reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the Panasonic Service Center or an experienced radio/TV technician for help. 1. This equipment complies with CFR47 Part 68 rules. On the computer is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If required, this information must be provided to the telephone company. 2. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See Warning To assure continued compliance, use only shielded interface cables when connecting to a computer or peripheral. Also, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Installation Instructions for details. 3. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all area, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the FCC RF Exposure Warning: This computer is provided with total RENs, contact the local telephone company. PC Card slots that could be used with wireless transmitter(s), 4. If your telephone equipment cause harm to the telephone net- which will be specifically recommended, when they become work, the telephone company will notify you in advice that available. Other third-party wireless transmitter(s) have not been temporary discontinuance of service may be required. But if RF exposure evaluated for use with this computer and may not advice notice isn't practical, the telephone company will no- comply with FCC RF exposure requirements. tify the customer as soon as possible. Also, you will be ad- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. vised of your right to file a complaint with the FCC if you believe it is necessary. 5. The telephone company may take changes in it's facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make Responsible Party: Matsushita Electric Corporation of America necessary modifications to maintain uninterrupted service. One Panasonic Way 6. If trouble is experienced with this equipment, for repair or Secaucus, NJ 07094 warranty information, please contact Matsushita Electric Tel No:1-800-LAPTOP-5 (1-800-527-8675) Corporation of America at DIAL TOLL FREE 1-800- LAPTOP5 (1-800-527-8675). If the equipment is causing harm FCC RF Exposure Warning: to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Supplementary Instructions "CF-50 Series with Wireless LAN" 7. There are no user serviceable parts contained in this equipment. 8. This equipment may not be used on coin service provided by This equipment complies with FCC radiation exposure limits set the telephone company. Connection to party lines is subject to forth for an uncontrolled environment. state tariffs. This equipment must be installed and operated in accordance with 9. The Telephone Consumer Protection Act of 1991 makes it provided instructions and minimum 2.5 cm spacing must be pro- unlawful for any person to use a computer or other electronic vided between antenna and all person's body (excluding extremi- device to send any message via a telephone fax machine un- ties of hands, wrist and feet) during wireless modes of operation. less such message clearly contains in a margin at the top or This transmitter must not be co-located or operated in conjunc- bottom of each transmitted page or on the first page of the tion with any other antenna or transmitter. This computer is transmission, the date and time it is sent and an identification provided with a PC Card slot that could be used with wireless of the business or other entry, or other individual sending the transmitter(s), which will be specifically recommended, when message and the telephone number of the sending machine or they become available. Other third-party wireless transmitter(s) such business, other entity, or individual. In order to program have not been RF exposure evaluated for use with this com- this information into your fax software, you should refer to puter and may not comply with FCC RF exposure requirements. the manual of the Fax software being used. 3