Panasonic KX-HN1032W Operating Instructions - Page 27

Timer, Managing camera units, Configuring the sound sensor, sensitivity, Registering a camera unit

Get Panasonic KX-HN1032W PDF manuals and user guides View all Panasonic KX-HN1032W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Programming R To enable detection for a disabled cell, select the disabled cell. a MOKN 6 When finished, press M N a MMENUN repeatedly to exit. Configuring the sound sensor sensitivity 1 MMENUN 2 MbN: "Sensor Settings" a MOKN 3 MbN: "Sound Sensitivity" a MOKN 4 MbN: Select the desired setting. a MOKN a MMENUN repeatedly to exit. 2 MbN: "Camera Management" a MOKN 3 MbN: "Add Camera" a MOKN R An operation guide is displayed. Press MOKN to continue. R Complete the following step within 90 seconds. Camera unit: 1 Press and hold M N for 3 seconds until the LED indicator starts blinking. Note: R A message is displayed on the monitor unit to show if the registration was successful or not, and a beep sounds. Timer The timer can be used to play sound from the monitor unit after the specified number of hours has passed. The timer can be set to sound once or repeat at specified intervals. 1 MMENUN 2 MbN: "Timer" a MOKN 3 MbN: Select "Once" or "Repeat". a MOKN 4 MbN: Specify when the timer is set for. a MOKN a MMENUN Note: R Timers play for 1 minute. Press MOKN to stop a timer. Press and hold MOKN for 5 seconds to stop timers from repeating. R If the monitor unit is turned off after setting a timer: - "Once": The timer will be canceled. - "Repeat": The timer will be played once the specified time has passed from when the monitor was turned on again. Managing camera units Registering a camera unit Monitor unit: 1 MMENUN b b Resetting a camera unit The camera unit settings saved on a monitor unit can be reset. Note: R All camera unit settings except for registration settings are reset. R Settings for all camera units registered to the monitor unit are reset. 1 MMENUN 2 MbN: "Camera Management" a MOKN 3 MbN: "Reset" a MOKN 4 M N: "Yes" a MOKN R A beep sounds from the monitor unit when resetting is completed. Canceling a camera unit Note: R Only the currently connected camera unit is canceled. To cancel other camera units, select the displayed camera unit (page 21) and then cancel that camera unit. 1 MMENUN 2 MbN: "Camera Management" a MOKN 3 MbN: "Delete Camera" a MOKN 4 M N: "Yes" a MOKN For assistance, please visit http://shop.panasonic.com/support 27 HN4001_(en_en)_0517_ver.020.pdf 27 2019/05/17 13:53:00

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
R
To enable detection for a disabled cell,
select the disabled cell.
a
M
OK
N
6
When finished, press
M
N
a
M
MENU
N
repeatedly to exit.
Configuring the sound sensor
sensitivity
1
M
MENU
N
2
M
b
N
:
“
Sensor Settings
”
a
M
OK
N
3
M
b
N
:
“
Sound Sensitivity
”
a
M
OK
N
4
M
b
N
: Select the desired setting.
a
M
OK
N
a
M
MENU
N
repeatedly to exit.
Timer
The timer can be used to play sound from the
monitor unit after the specified number of
hours has passed. The timer can be set to
sound once or repeat at specified intervals.
1
M
MENU
N
2
M
b
N
:
“
Timer
”
a
M
OK
N
3
M
b
N
: Select
“
Once
”
or
“
Repeat
”
.
a
M
OK
N
4
M
b
N
: Specify when the timer is set for.
a
M
OK
N
a
M
MENU
N
Note:
R
Timers play for 1
minute. Press
M
OK
N
to
stop a timer. Press and hold
M
OK
N
for
5 seconds to stop timers from repeating.
R
If the monitor unit is turned off after setting
a timer:
–
“
Once
”
: The timer will be canceled.
–
“
Repeat
”
: The timer will be played once
the specified time has passed from when
the monitor was turned on again.
Managing camera units
Registering a camera unit
Monitor unit:
1
M
MENU
N
2
M
b
N
:
“
Camera Management
”
a
M
OK
N
3
M
b
N
:
“
Add Camera
”
a
M
OK
N
R
An operation guide is displayed. Press
M
OK
N
to continue.
R
Complete the following step within
90 seconds.
Camera unit:
1
Press and hold
M
N
for 3 seconds until
the LED indicator starts blinking.
Note:
R
A message is displayed on the monitor unit
to show if the registration was successful or
not, and a beep sounds.
Resetting a camera unit
The camera unit settings saved on a monitor
unit can be reset.
Note:
R
All camera unit settings except for
registration settings are reset.
R
Settings for all camera units registered to
the monitor unit are reset.
1
M
MENU
N
2
M
b
N
:
“
Camera Management
”
a
M
OK
N
3
M
b
N
:
“
Reset
”
a
M
OK
N
4
M
b
N
:
“
Yes
”
a
M
OK
N
R
A beep sounds from the monitor unit
when resetting is completed.
Canceling a camera unit
Note:
R
Only the currently connected camera unit is
canceled. To cancel other camera units,
select the displayed camera unit (page 21)
and then cancel that camera unit.
1
M
MENU
N
2
M
b
N
:
“
Camera Management
”
a
M
OK
N
3
M
b
N
:
“
Delete Camera
”
a
M
OK
N
4
M
b
N
:
“
Yes
”
a
M
OK
N
For assistance, please visit http://shop.panasonic.com/support
27
Programming
HN4001_(en_en)_0517_ver.020.pdf
27
2019/05/17
13:53:00